Routing

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

Labels

Forum Posts

Hi experts,Scenario is that we have 837 router and Cisco 2960 switches in branch office. What I am trying is to divide lan network in two vlans. But 837 doesn't support vlans and 2960 doesn't do inter vlan routing. So is there a way I could setup thi...

What is the determining factor on a router resetting. My router keeps resetting due to the amount of connections around 600 - 800. I am a PC power user and run a Slingbox, webserver, I use VPN, I nearly max out my entire cable connection and have 10 ...

following is a copy of sh redunancy of m 4510R, I just reset the config register to 0x102, is this setting correct for it to comeback up at reboot? (0x102) it is the default at bootup isnt it?...BOOT =bootflash:cat4000-i9s-mz.122-25.ewa4.bin,1;BOOTLD...

davisr651 by Level 1
  • 538 Views
  • 2 replies
  • 0 Helpful votes

Hi I hv 2 2811 routers for internet. On one router ADSP link is terminated & on another router I have MPLS inernet link is terminated. I want to segregate the trafic on both the link. which I did via Route-map. Now I want to implement failover betwee...

If i use telnet to connect to routers and switches using username and password authenticating via tacacas, Travel username and password in clear text ?, i need implement ssh?,

I have to do some reconfigs on my routers that form my internal corporate WAN and am not sure how to remove a serial port. I'm using VWIC-2MFT-T1 cards for these specific connections that have to be torn down and rebuilt. When I install the card an...

qbakies11 by Level 1
  • 3526 Views
  • 3 replies
  • 0 Helpful votes

My apologies if this is completely off-topic, but I was hoping someone may be able to point me in the right direction as I don't want to open a TAC unecassarily.We have an SFP adaptor (GLC-ZK-SM) that was connecting to a CISCO 3825. The adaptor stop...

mariov652 by Level 1
  • 513 Views
  • 2 replies
  • 0 Helpful votes

Hello everybody It is my first time writing here and I would like to thank you for spending your time on my question. So,I am a CCNA candidate and I came up with a problem.I connected back to back two cisco routers (2610XM using the low speed serial ...

Hello,Going for an IPV6 lab where multiple points of redistributions between RIPng and OSPFv3 exist, I was looking for a command to manipulate administrative distance in order to prevent sub-optimal routing, as I usually do IPv4.In IPV4 we have this ...

ccr_cisco by Level 1
  • 1397 Views
  • 2 replies
  • 0 Helpful votes

Hi we have a 6509 running 12.2(17d)SXB11 with a strange errorA LES 100mb circuit is plugged into port gi4/48 L3 (copper) when utilisation of this hits 100% it causes extreme packet loss on ports gi1/48 and gi1/41 which are completely un-realted (one ...

jmoss1 by Level 1
  • 821 Views
  • 4 replies
  • 0 Helpful votes

We've 7206 vxr router with atm oc-3 interface.Our branches are connected the hub site via p2p ATM port,we have no encryption on the links and we want to migrate this links to ipsec vpn tunnels and hub&spoke topology.What is the best solution for this...

tdorduncu by Level 1
  • 548 Views
  • 4 replies
  • 0 Helpful votes