Routing

Hi,I have my router A connected to router B through ethernet.Router A also connected to router 1 through dialer.I am recieving Eigrp route 1.1.1.0 from router B as EXD with distance 170., also reciving route from router1 as distance 90,so this get in...

Pls tell how to upload .tar file to flash and ativate boot image?And what form following IOS I can use to restore booting of the switch. In my 2950 flash and nvram are erased with command:"erase nvram" and "erase flash".C2950 EI AND SI IOS CRYPTO IMA...

HI. Im not sure if this is the right forum or not, but Ill try. I need to configure a C3250 Router which has wireless built into it. It has the RPTNC connectors out back for the antennas. When I console in, there doesnt seem to be any reference to t...

Hi Guys,Please help me out to understand that how the packet travels from one computer to another in the following scenario :-Router A is connected to Router B by a serial cable. A local network of 192.168.1.0 is connected to the fastethernet interfa...

Hi Guys,I am new to networking so please help me.If one computer is connected to first port of the switch and second computer to the 2nd port then how the frame will travel in the network.Thanks and RegardsSumit Goel

Hi,Is there a possibilty to hide the telnet username on a IOS device?? On the Firewall the output is "****" instead the clear text of the username.kind regardsnorbert

Fellow Net Pro'sI am currently working on a new data center design that will be housed at a co-lo facility.What I was wondering is if I assigned a loopback address to every device that I have on my diagram. Does it make sense to use it as the router ...

We have a Cisco 1841.Fast0/0 with 30.104.104.2 (IP to ISP)FAST0/1 with 30.103.103.129/27 (our public ip block)I like to specifically block any incoming (from internet) access from port 1-1024 to only 30.103.103.135 (one of our public systems)How can ...

Hi, I'm trying to get some information on how load balancing on 2 WAN links can be achieved before I have a meeting with our WAN provider and bosses.We are getting 2 lines which are 40mb each with will give us an 80mb line in load balance mode. I wa...

Hi,I have 2 Layer 3 Cisco 3560G switches,I have cascaded these two.Now I have 30 bladed servers in Server VLAN,in that is it necessary to configure the Server VLAN in both 3560G switches.Then there is a SUN NAS server,which has 2 GBIC NIC card,they h...

Tunnel1 is up, line protocol is up Hardware is Tunnel Internet address is 172.16.101.109/24 MTU 1514 bytes, BW 1000 Kbit, DLY 10000 usec, reliability 255/255, txload 2/255, rxload 1/255 Encapsulation TUNNEL, loopback not set Keepalive not se...

Hi,I installed a Cisco 2821 DIA router. I am able to ping the ISP's router. An Win XP laptop connected witha cross over cable can not browse the Internet. The XP PC was given a static IP in the routers Ethernet IP block. The configuration of the ...

Hello,I have a Hub and Spoke setup with 3 remote locations. All using Point to point 3MB bonded T1's. We have help desk personal that go to these remote sites maybe once or twice a week for support. When they get to the site they usually remote deskt...

I have 2 offices at diffrent locations, both the offices are connected through ISDN BRI link (128 kbps). I have a 2811 router at the head office and an 1841 router at the remote office. I have configured it in a dial on demand mode. The IDSN bri conn...