Routing

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

Labels

Forum Posts

Hi all,I'm currently having issues regarding RSTP on a simple switch network, scenario is as follows. I have 2 switches directly connected to each other over a trunk link (dot1q). These 2 interfaces have the following identical config. interface Giga...

Hi what are command required for voice and data traffic?Case 1:Let say voice is vlan 100 and data vlan 200.Case 2:Voice Vlan0 ( by using dot1p )and data will be native.-V

Folks, what's the minimum image I should use if I need to run BGPv4 on my 2851 router? I know that the c2800nm-advipservicesk9-mz.124-9.T5.bin will do BGP for example, but my question is, is this the image the one can give me BGP and it is the most c...

news2010a by Level 3
  • 667 Views
  • 3 replies
  • 0 Helpful votes

I have just got a few 2611 dual ethernet routers running IOS 12.2(17) and start setting up my home lab. But I am running into "no routing" problem.I already have a home network 192.168.0.x/24 and the default gateway is 192.168.0.1. I set the E0/0 o...

alexmchau by Level 1
  • 1120 Views
  • 10 replies
  • 0 Helpful votes

Hi All,I am trying to configure my second interface to reach outside world on my ASA device. From machines i could able to ping the seconf interface on the ASA and vice versa. But the machines are not able to reach outside world. I dout my NAT config...

caliber01 by Level 1
  • 1407 Views
  • 11 replies
  • 0 Helpful votes

Please i have a voip platform for fax and voice calls,unautorised users get access via ftp.pls i need access list statement to permit only 4 ip addresses on the 2600 series and all other attempts denied.i await sample config to load on my router than...

Hi there, I have got an 1841 (adsl) router that is stuck in a boot loop, I have tried changing the 32mb flash card to a known working card , but the problem is still there.I have attached a bootup trace.Would a ROMmon upgrade help? Is there a way to ...

honeyss07 by Level 1
  • 1518 Views
  • 3 replies
  • 0 Helpful votes

I need a hand on getting a P2P T1 up and running. I have an up/down link. I am using static routes and have tried using bgp but nothing is bringing the link up.Serial0/1/0 is up, line protocol is down Hardware is GT96K with integrated T1 CSU/DSU D...

I've a customer who uses IPX over GRE,in a hub and spoke topology. A recently installed router fails to pass any IPX over the tunnel. The configuration cannot be any simpler, IPX networks on the GRE and Ethernet interfaces and ipx routing enabled glo...

aacole by Level 5
  • 401 Views
  • 1 replies
  • 0 Helpful votes

Dear all,I have three remote offices. they connected together with E1.I have also three pbx in each location.I want to use VWIC cards to integrate voice and data for this solutions.is there any sample and web link to guide me?

emadehsan by Level 1
  • 489 Views
  • 3 replies
  • 0 Helpful votes

Hi,After changing our config from normal to vrf lite , my taccas is not working, I had same isssue with ntp but assign the config with vrf as below, "2ntp server vrf lite7200 10.190.2.1" and its start working,Please see my config below for TACCAS,i ...

Hi,I would like my ISDN couter to dial two different numbers/IP. In case the firt number is not available it should dial the second number. could you tell me what is the command?thanks,Arana

rana_beech by Level 1
  • 1234 Views
  • 14 replies
  • 0 Helpful votes

We are currently using Nortel Contivity VPN devices between London and International Offices. Unfortunately the Service Provider has let us countless times and we are now putting in a leased line between one of the branch offices and London. The a...

jayamistry by Level 1
  • 2524 Views
  • 26 replies
  • 0 Helpful votes