hi, here is my scenario setup,host A - - router A -- PE 1 --- PE2 ---GRE tunnel over AT&T EVPN circuit----PE3- router B- host BI am currently setup MPLS over GRE tunnel with Cisco ASR9901, i have configured MTU 1400/ TCP- MSS-adjust-enable on tunn...
Forum Posts
Hi,I have a new network attached to me with its own RP. I need that network to join a multicast group that my RP hosts but I cannot change the RP of the new network. How would I accomplish this?Thank you for any advise.
Resolved! ASR-1001HX and BGP
We have a pair of ASR-1001HXs and each is receiving a full BGP table from their 4 neighbors (3 eBGP and 1 iBGP). This platform is capable of 3.5 million IPV4 routes with 16GB of memory (which we have). I am wondering if I'm hitting the 3.5 million ...
Resolved! VRF interface assign issue
Hi I am getting an error while assigning IP vrf forwarding F-1 command under the interface R38(config-if)#ip vrf forwarding ?F-1 VRF NameWORD VRF namef-1 VRF NameR38(config-if)#ip vrf forwarding F-1% Use 'vrf forwarding' command for VRF F-1R38(...
Dear Experts,We have a problem about eBGP configuration.Now my customer need config 2 physical circiut to our network.The first circiut use for internet traffic, other circiut use for peering between IXPs in our country.We think, we create 2 neighbou...
Resolved! receive bgp but not in routing table
Hello, im new and currently learning bgp i wonder if im missing something here, currently Border Cirebon received bgp advertised from FO but there's none in routing table here is the topology thanks in advance
Hello,On a 3750-X switch I can ping an IP of a local VLAN interface but it is not possible to do a traceroute to this same IP !3750X48T#ping 10.64.10.6 source 192.168.2.203 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 10.64.10.6, ...
Hello,My Device Cisco 920i Router has hang and after reboot the router has came up, When im take console during hang ..im getting FPGA fail logs... PLs suggest what is FPGA and why my router has going hang mode ??
a c1111 with a build in lte modem (cellular 0/2/0) and a second LTE connection on its WAN port (Gi0/0/0) from a mikrotik modem with lte passthrough GigabitEthernet0/0/0 xx.xxx.183.118 YES DHCP up up Cellular0/2/0 yy.y...
if i connect to my home network with AnyConnect i get really poor download speeds of 1.5Mbps (trying to watch a movie stream) disconnect from the vpn and use a forwarded port i get the expected 15Mbps speed where could the problem be thats a differen...
Resolved! SNMP
We are using Cacti for monitoring. So the question is Could SNMP slow down the network?
I was wondering if anyone could offer any ideas \ insight for an issue we currently have at the company I work for (basically poor performance on DMVPN tunnels i.e download \ upload speeds). We have an overlay network which operates on a hub \ spoke...
Can the WAN interface be bridged with a LAN port? I've already got a router on my network and I want to use the C1117 just for it's VDSL interface. With the old Cisco 877 I used a bridge group on the ATM0 interface and BVI but it seems that's not sup...
Hello I have a SG500X with 2 PBR’s. LAN 192.168.5.1-32 use GE 1/1 192.168.1.2 for Internet AccessLAN 192.168.5.33-64 use GE 1/2 10.0.2.2 for Internet Access. LAN Subnet 192.168.5.0, regardless of their Internet access communicate via same Subnet. GE...
I have a 800-Series router connected in the following configuration:Port GigabitEthernet7 is connected to an external server (192.0.2.251) that sends unicast UDP to destinations 192.0.2.42:45100 and 192.0.2.44:45100Port GigabitEthernet1 is connected ...
