Routing

Hi,I have an MPLS connectivity between two branches. I have created a tunnel between two router interfaces.I would like to configure priority queining on the Tunnel interface. (with acl defined priority groups high/medium/low/normal) Is there a way t...

Hello,How can I make a GRE tunnel betwen cisco router and ADSL. What is the configuration of GRE tunnel if other side of the tunnel has dynamic IP address.Thanks in advance

Through acquisition, we have acquired another comapony with a different carriers MPLS network. On my native network we run bgp as the routing protocol accross carrier a's MPLS network. The acquired network organizations network is based on OSPF wit...

After upgrading from version 12.1(21) to 12.1(27b) this error message were posted:%DBUS-3-NOSUPPORT: No driver support in this image for CIP2 in slot 0 (card type 13) - disabled%RSP-3-NOSTART: No microcode for CIP2 card, slot 0.The CIP2 microcode ver...

Hello all,I'm using a cisco 2811 IOS c2800nm-entservicesk9-mz.124-5.bin with 4 VWIC-2MFT-E1 modules connected with eight E1 atm link configured with 2 ima groups.Even if i've replaced wic and cables i continue to receive these error:*Aug 29 13:50:19....

I have a 7604, that has one vlan, associated with one switchport. I am seeing dropped packets on the L3 interface, but not the L2 interface. What would cause this? Do I have a backplane issue on this device?

What is needed for complete connection with a cisco PIX 515 and cisco vpn client software for windows v.4 & up?

Hi!We have a 6513 switch - our problem is whenever we create any new vlan apart from default vlan1 we get an error message "error exiting config-vlan mode 29: Bad domain name length". The switch is in transparent mode and shall remain so once it star...

I have a 500 node MPLS network. All the remote routers are 2811's and all the remote traffic terminates here at the central site on a 7606 with a DS3. We have implemented service policies in all the remote routers and they seem to be working well. ...

Basically, I have two sites connected by a 100Mb Colt line with a Cisco 2600 at each end and then at each site I have a 3750 cluster providing LAN switching, routing etc.I have set up each site to have the same VLAN numbers; VLAN10 - Servers, VLAN20 ...

Connecting two remote site with Lease line one side ETH link other V.35. Its a 2MBPS link. Which V.35 router to select. We nned to run ERP softwares simultaneously on 5 machines.

Dear All,I am deploying a network using 3825 at cental location and 1841 at 3 branches.Central Router has two PRI lines. One Channelized E1 line is terminated on VWIC-1MFT-E1 and other PRI line on NM-1CE1T1-PRI.all Remote 1841 routers in branches ha...

Hi,In one branch office, We have 1841 that has ADSL modem connected to FA port. Behind the 1841 is the private LAN. The ADSL line (dynamic IP) is used for L2L VPN to connect to two sites and also to connect to Internet - browsing, downloading, etc. ...

Dear All,i had Cat.4506(IOS)is backup and Cat.4006(OS)is primary.so i would like to do on port switch redundency( i mean if connection primary down, it connect to backup line automatic.Please see the attach file.Please advice me on this case.Best Re...

Hi, I two 7204VXR routers (IOS 12.2-46f SERVICE-PROVIDER feature set) each connected to a different service provider with bgp running over them in a multihomed inbound config.HRSP is implemented on the internal interfaces while tracking the external ...