Routing

Voila ce que nous voulons:Mettre en place un lien de 155M avec un FAI externe via la Fibre Optique.Nous voudrons savoir le type de routeur ainsi que les modules qui lui sont n?cessaires pour pouvoir mettre en place ce lien.Merci de bien vouloir nous...

HI!What is the default between show run & show config?is it the same?or there is a different?10xsRegards

router ospf 7router-id 192.168.250.9redistribute connected subnets tag 9network 172.16.9.0 0.0.0.255 area 0In the above config, what's the meanning of "tag 9" in redistribute cmd line?

hello all , I have here a strange problem , loopback IP configured on the router for Mgmt . and I can't ping or telnet this IP when checking CEF I can seerouter # sh ip cef 10.1.1.1IP-address, version 202, epoch 0, attached, connected0 packets, ...

HI EXPERT's!I Have Read the following on some linke provided by E.Amit in some Post:In this example, a customer is connected to an Internet service provider (ISP) by a T3 link. The ISP wants to rate limit transmissions from the customer to 15 Mbps of...

Does Cisco 3800 routers support DS3 or T3 Technology. If not, What Cisco Router will support DS3 or T3 Card?Thanks,

I have an 1821 router with VPN configured between two sites. On one of the routers i keep getting messages in Log file - "critical memory allocation of 65548 bytes failed from 0x400C615C, alignmet 32. When I do a show buffers the normal buffers, 15...

I cuurently have 2 T1 circuits and would like to have a single host only use 1 of these T1's and all other host on the second T1. In case of a failover i would like to have it failover to the other T1. Is this something that is possible to complet...

Here's an odd one for you:I have a 2821 with a WIC-1CSU-T1 that's been running 12.4.2T2 for over a year with no problems. I tried to upgrade it to 12.4.6T5 and as soon as traffic starts to pass through it I get MAJOR errors and overruns. If I roll ...

Good day;I'm trying to set up a BGP connection but the peers never connect. When I do a sh BGP neighbor I see No active TCP connection. I also ran a debug and get the following:Mar 16 16:35:02.512 UTC: BGP: 10.128.72.154 open active, local address 1...

I have 1 particular IP address that I can't remove in a standby group that contains at least 20 IPs. On the router that is in standby mode for that group, I can remove other IPs, but I can't remove this problematic VIP. Any suggestions? Oh yeah, I...

Hello all, I have just reconfigured a 851w. with Inside global and Inside local addreses connected to a cable modem. The test function of SDM 2.3.3 passed everything as O.K but when I try to ping from the CLI, I was getting no where.Furthermore f...

Hello, I have an ISDN card in the router along with th one onboard, both are recongised fine but the issue is in the running config both show as Bri0, I have no way of configuring the ISDN card, ANY IDEAS?Config attached Thanks in advance

I have a router with two adsl lines, one primary, one backup, terminated to the same LNS. I want to assign a static route for the same network to each of them with a higher administrative distance for the second and I want to do it via radius using c...

Hi,consider following small frame relay network: [r1] | Se0 | / \DLCI 102 / \ DLCI 103 [r2] [r3]Configuration of frame relay is done entierly on main serial interface on all routers (i.e. sub-interfaces a...