Hello, Consider below topology, in which there are 3 Routers.1. R1 and R2 are connected and default router is configured on both the routers towards each other.2. R1 and R3 are connected and OSPF is configured on both the routers and3. R2 and R3 are ...
We still have Cisco 3845 routers in our infrastucture, each router has a single 512 chip. We are starting to have memory chip failures, we have spares and that gets us by but my question is - if I equip a Cisco 3845 with two 512 chips and either chip...
Dear all, I need to configure a Cisco C1113 (router B) to enable BGP Routing between two networks.Router A is already configured by my provider and I need to configure my router B, but I would need to make sure that my configuration is correct...Here...
I may very well be overlooking something as I am still very new to this but one of my practices for an exam coming up is having to be able to use 1 router(4221 it says), 1 switch (2960), and 2 pcs, and I have to create two subnets. It says in the ta...
i have this problem on my ASR 1002-X 19720 18557 57% 57% 57% S 295694336 mcpcc-lc-msthe procesor cpu0 is always 45% usedsometimes all processors are used but this happens by cpp_cp_svr and the router works very slow.
Hi , Is MACsec encryption supported either on port-channel or on member 10Gbps ports in a port-channel on a Cisco ASR1001-HX ?I am slightly confused looking at the documentation MACsec and MKA Configuration Guide - WAN MACSEC and MKA Support Enhance...
Hi, I need to choose an ASR1000 model to support 4000 branches, with 3 tunnel in each branch and with 50G to 80Gso which model should I use?
I have a Cisco Router (3825) that I have been trying to make a connection to a PEAP network for my lab. The supplied credentials for the PEAP (802.1x) are a username and a password. Does anyone know how to use the 3825 to connect to a PEAP network us...
See attached for diagram: R1 advertises a router to R2 via the MPLS using BGP – On R2, I am going to redistribute the route into OSPF. From R2 to R1 the BGP would be the preferred path – How do I force R2 to use the OSPF link as primary route for tra...
Hi, I needed something like the below configuration on the router for TrustSEC router to router link. interface GigabitEthernet1/0/10description for TRUSTSEC TESTINGcts manualno propagate sgtsap pmk 00000001234ABCDEF mode-list gcm-encrypt But on the ...
Hi, I'm trying to set up IPv6 over IPv4 IPSec on a C1101-4P with IOS-XE 16.12.04, but the IPv6 packet silently disappears. Crypto works fine with only IPv4 (tunnel mode ipsec ipv4), traffic works both ways.Switching to IPv6 over IPv4 (tunnel mode ips...
I'm not sure what I've done wrong here and why the laptop isn't connecting to the router. Please help.
Hello, I need to isolate a population connected on some dedicated peripherical switches. These peripherical switches are connected on a WS-C3750G-12S-S. Ip routing is enabled on these switches. Vlan Level 3 with ospf process is running between the ...
Hello,I have two networks (net1 & net2) in one site (Site A) and two networks (net3 & net4) in another site (site B), I want to connect the two sites but by isolating the access so net1 can access net3, and net2 can access net4. Leased line of 300Mb...
Hi, There, Here is my topology, --------L2TP-------(local lan)G0/0/0--------------------Loopback0-----------g1/0/2(remote lan) There are static and bgp route. i have 2 questions: 1. i don't see any redistribute static setting ...
