Routing

I ahve a 3700 with isdn bri card. I have 63 with the same config and they all work except this one site. My debugs which are shown below appear to me to be a telco issue. My telco tells me it is the hardware. I have repolaced the rj-45 to the jack- t...

Hi,I am trying to configure a router to convert a XOT SVC session to a PVC session.Host app - XOT SVC - Router - X.25 serial PVC.There is a small section at http://www.cisco.com/en/US/tech/tk713/tk730/technologies_configuration_example09186a0080094a4...

dears can 1721 router act as a proxy server for users want to access internet if yes pls. send the configuration for this issue

I need to provide multicast access accross our WAN which are connect over an MPLS network provided by a 3rd part provider.I control the CE devices but the provider has controll of the PE.Is there way to configure Multicast routing such that it van tr...

Does anyone know were to find a data sheet on the NMD-36ESW? Specifically I'm wondering what the bandwidth is on the switching fabric. Also the only info I see on STP is it supports 802.1d - what about 802.1w, RSTP?Thanks.

I have a routing question.Previous configuration:3620 with 2 T1 lines to a 3640 (in the central office). I would do a show ip route and both lines would show up for the subnet in either router.New configuration:3620 with 3 t1 cards. (two are the sam...

how do you nat a 11.0.0.0/8 network to a 10.0.0.0/8 network in a cisco 877 router. ie 10.1.143.251 to 11.1.143.251 and so on. i am trying to nat a specific address in a 10. network over to the relative 11. network.

I need some assistance from some of the more experienced Network Designers out there.Here is the situation. I have a customer whom has 2 Edge routers. Both of the Edge routers connect back to the Same ISP. While the same ISP provides the services, ...

I have a PIX 515E running 6.3. I want to NAT the destination address of a connection. All the examples I am able to find concetrate on NATTING the source address.example:User types ftp 10.1.1.2His source is 10.1.1.1 and the destination is 10.1.1.2Whe...

I am using this command on a 3485 router to export from 4 interfaces out a 5th Ethernet interface. The purpose is the use of a web control filter. According to the logs the export-traffic is not dropping any packets. However according to the web f...

I have a scenarion where HSRP is configured on my devices. There is a " Redundancy HSRP <Group number>" command given on the Static NATs configured.Ex: ip nat outside source static x.60.2.20 x.27.13.202 redundancy HSRP17Now, as per my understanding ...

Hello:My problem is in my logging history :%SYS-3-TIMERNEG: Cannot start timer (0x81858EB8) with negative offset (-5000).-Process= "IP Background", ipl= 0, pid= 31-Traceback= 802D893C 80539B08 8053BE44 8053BF9C 80534E14 803DD624 803DD6B4 803C5B44That...

Hi.I have some 2950 switches conected in a 3550. STP is enabled in all switches of my topology, but just part of it could have loop problems, (vlans 6, 7 and 8) so I am thinking about disabling STP in some switches so I could reduce the number of mul...

One of my students has changed the config register on our 1601 to 2D32 which means I am unable to console into it. There are no other settings on the router so telenetting in is a no. Is there a reset switch anywhere? I believe these settings change ...