Routing

Hi All,I have a Cisco 2610 Router having IOS version 12.2(29a). I want to run isis protocol on this router but unable to do this. When I enter " router isis " command in configuration mode then the prompt does not change to Router(config-router)# mod...

I want to integrate two Networks LAN A------- 134.65.32.0/20LAN B--------134.65.47.0/24Router B has spare Eth port.How packets will be routed between LAN A and LAN B .Please specify the config .

What do we mean by Layer-7 Switch? How Layer-7 switch is different from Layer-3 and do we have any layer 7 switch in CISCO ( i know it is there but wanted to confirm with experts before i answerThanks in advance :)

Recently i bought a 7206VXR with NPE-G1 , I found the 7206VXR only have boot image on the router ,so i delete origin boot image then download "c7200-is-mz.121-27b.bin" , finally the router directly run into romon , I have some question1. there is mus...

I am not experienced at adding an additional T1 to an existing ima group.This is the 4th of 4 T1s. The basic interface is already configured. I believe I need to add the atm1/3 interface to the imagroup? This will make the bandwidth 6M rather than th...

Hello,I have a switch catalyst 2960 and i need do rate-limiting in a port fastethernet.In the configuration guide in the chapter of Configuring QoS says as to do it, and I configuration:configure terminalclass-map clasepolicy-map politiclass clasetru...

Does it support OSPF?I tried to configure, I enable it by doing ip routing. Then routing ospf 1842. It takes it but it does not configure it, it does not go into the subline nor it appears in the startup config file.Any comments would help.thanks

Hello,I would like to know how to disable http so when I go to http://192.168.1.1, I dont want see userid & password prompt.

Hello,I would like to know how to disable http so when I go to http://192.168.1.1, I dont want to userid & password prompt.

R1, R2 & R3 are fully meshed with R1 & R3 learning EBGP routes from another two AS ? R2 has no EBGP peers.When I configure R1, R2 & R3 with no synchronization they each show all the IBGP routes advertised by their IBGP peers and these routes are ente...

We just hooked up a IGX 8430 32 slot rackmount chassis. Slots 1-16 work fine and slots 17-32 show up as "empty".When cards are plugged into the lower shelf (slots 17-32) we get ""Empty 31 HW failure" (31 beingthe among the slot we tried)". The SCM ...

Brand new 1841 router. Connected to the console and ran through the initial setup, changing the enable secret and enable passwords. After setup I did a conf term and entered the following - no username cisco, then wrote the config to memory. The r...

I?m trying to connect a branch office to head office using two 1841?s across a T-1 line.I?ve got communication between the routers across the T-1 using a static route, and from each router to the locally attached Ethernet LAN. I do not have communica...

Hi All,Can someone tell me the difference between doing the following:ip route 10.0.0.0 255.255.255.0 FastEthernet1/0andip route 10.0.0.0 255.255.255.0 10.0.0.1I did the first one on my router to begin with and it did not work, but the second did. W...

Hello,I am in the process of ordering a 3800 series router for Japan. I've never ordered internet connection out-of-US before. what are some of the concerns I should be addressing with Japan's ISP?I also would like to know what WIC is appropriate f...