Routing

I have configured an accounting functionality on a 7609 sup7203bxl. The accounting is based on the class-base QoS MIB.I have attached the service policies on several VLAN interfaces, the VLANs go out over the same 10 GE interface. Question:What is th...

Hi Will the configured BC figure affect the frame size to be transmitted (e.g. MTU)?For example, there is one switch configured as: class important police 10000 1000 5000 conform-action transmit exceed-action dropWill the packet exceeding 1000 b...

We have 2 firewalls connected to our 6509 with MSFC, and want to route all internet traffic on a certain vlan to a firewall that is not designated as the default route on the msfc? is this possible?For example.Here is the default route:0.0.0.0 0.0.0...

Is anyone aware of any limitations regarding the number of interfaces that can use IP CEF?

Hi all,I have a 2821. Let's say it has four interfaces:- Net 1, a point-to-point link to an ISP- Net 2, owned by customer One- Net 3, owned by customer Two- Net 4, also owned by customer TwoThe bandwidth provided by the ISP over Net 1 is a symmetric ...

HiPlease refer the attached diagram.What is the best possible way to implement redundancy for the link between HO and branch offices? ie. In case of a failure of link between branch 1 & HO traffic should pass through the link between HO & branch 2 a...

Hi, We are having QoS implemented on 3550 switches.We have decided to replace 3550 with 3750 switch with QoS same as on 3550. But when I entered the queueing commands of 3550 on 3750 I got errors on following lines....Errors....Router(config-if)#mls ...

Router A is connected with Router B with 64k Link and to Router C with 128K link.Router B and C are again connected to WAN cloud and both are receiving Routes via EIGRP with different metric values. These routes are being sent to Router A.Now Router ...

I need loadsharing packetwise over the switchports(WIC-4ESW). Layer 2 portchannel doesn´t work. Loadsharing over eigrp works sessionwise. Have anybody an idea?

Hi,We have an 1841 with a serial WIC which is configured:FastEth0/0 connected to the internal LANFastEth0/1 connected to a sat conn (internet) Serial0/0/0 connected to a frame conn (internet)FastEth0/0 has 192.168.1.21 and 1.20 (secondary) bound to i...

My internet come on two ethernet interfaces. One is satelite(two way), the other is ADSL. Satelite is primar, adsl is secondary. I want when primar conection(satelite)will be about 75-80% full, to start to work the secondary conection. And also adsl...

Hi,I have one question regarding ospf and Eigrp administration distance.If eigrp injects external routes it changes its administartion distance. But in case of Ospf it remains the same. Why it is the case ?can any one explain with example. or refer s...

Dears,configure so that RP spoofing should not happen on R1 loop0R1 ip multicasting-routingloopback 0ip address 1.1.1.1 255.255.255.255ip pim spares-dense-modeinterface e0ip address 10.1.1.1 255.255.255.0ip pim sparse-dense modeip pim send-rp-announc...

I'm updating my routers form feature set: I¨P-ONLY to ENTERPRISE/FW/IDS PLUS IPSEC 3DES, but I realized that the new feature set don't support the "secret" command used instead of the password on the users.In my IP-ONLY version I had the users config...

Hi,Just wondering what is the reason for seeing the following for monitor session 1 being the SMS?sh monitor session allSession 1---------Type : Service Module SessionIs this normal behaviour in my config i dont see anything which r...