Routing

Hello all, I have inherited a Cisco 2610 with a serialWic console, and ethernet port. It is running 11.3.4 which is old. When I connect via console cable, and power it on, I can see the post and the normal bootup information. Then when I try to hi...

I have 1711 router connected to internet on 128Kbps. Recently we upgraded our line to 512K. After that i couldnot connect to the internet. Do i need to change anything in the router, like specify the 512k bandwidth, what are the commandsregardsshoeb

Hi alli want to connect 4 e1 links to my branch office, i want to achieve 8 mbps link, i want to bundle these 4 e1 lines to work like single e1 line.is it possible? what are the cards required for this?kindly suggestRegdsBinoy

Can a 2821 router IOS Version 12.3(8)T5handle SSH sessions on vty lines?if so could you give me the commands?thanks in advance

Here is the scenario:I have to locations connected via a T3 with a VPN/GRE tunnel for backup. If the T3 fails traffic is re-routed almost transparently across the VPN tunnel with the exception of Citrix traffic. Because of the few seconds it takes ...

Dear Friends,I have 2 wan location with 1700 series Router-A and Router-B conencted with Serial connectivity.The LAN Network at Router-A and at Router-B is in same subnet. Eg 150.10.0.0/16 at end A and 150.10.0.0/16 at end B.Now since both side lan s...

Hii have a router with 3 links to ethernet all of the same isp, and i want to configure load balanced over the 3 links, i dont have any routing protocol, i only have a default static to the isp router, how can i configure load balanced? do i need to ...

Hello,I have a 1751 Router which connect to ISP1(Lease Line). For the Internet Connection, I have faced many problem with the connection, sometimes disconnect(not stable). So that's why I decided to connect to one more ISP( ISP2, SDSL). What am i goi...

I have the following network setupremote--PVC1--R1in--PIX1--R1out--Provider --PVC2--R2in--PIX2--R2out--Between the remote and r1&r2in I am running EIGRP 10. Between r1&r2out and provider I am running EIGRP 100.I am looking to have full redudanc...

Hi I have the following problemI am trying to open some ports on the Cisco 800 router so people from outside can use ftp and vpn.ive got 1 server with ip 192.168.1.30the problem is when i check with grc.com on open ports ,it says there stealthed so i...

Hey all, I have done MLPPP before awhile ago and never really needed to know exactly how it load balanced, Mostly becuase it was a simple 1,2,3,4 full T1'sBut does anyone know of a good document or a way to setup MLPPP to use T1's that might have a d...

Hello,I would like to ask how can I order the ATUC-4FLEXIDMT linecard for my 6260 DSL switch. The configurator only shows the following: ATUC-8-DMT-I-1,STUC-8-SHDSL-1 and 6260-ATUC-8DMT-1. Is this card replaced already? If it is what's the relacement...

hi,how can i deny icmp on my adsl interface?thanks a lot.

Hello,I am working on an implementation of a hub and spoke WAN network using a HSSI network module in a 3640 connecting to a Digital Link IMUX. We are connecting two T1's to start with and there are 22 remote sites with Fractional Frame Relay access...

Hi,I have two carriers, yIPes and SBC. The problem is that yIPes connects a little differently, in that I connect to a yIPes router, which immediately connects to one of their ISP's. The net result is that all yIPes routes have an "extra hop" of sort...