Routing

I have a problem configuring bgp on our system.configuration like this:isp1-Rtra-eth-Rtrb-atmpvc-Rtrc-eth-Rtrd-isp2there is a network 10.1.1.0/24 which is connected to Rtra. this network must be announced primarily to isp2 but in case of connection l...

I have 4 3600 series routers A,B,C, and D.A & B 3660 with 96 MB memory and 32 MB Flash memory.C & D 3640 with the following:C --> 96 MB memory and 32 MB Flash memory.D --> 32 MB memory and 8 MB Flash memory.i want to upgrade, first for A & B to 192 M...

Hello,Since we have a customer who is in the posession of a Catalyst6513 with cat6000:sup2k8.7-6-1 as image file and i would like to reproduce their material i went to the cisco site in search for this image. I can't find him anywhere...anyone who ca...

Dear Friends,I have a cisco 2651-XM Router.I was reseting the password and gave wrong confreg value by mistake.Later on i retrived the password by writting the correct confreg value.Now when after doing the configuration, writing it on memmory by Wri...

recently we changed our ISP and have connected to them using a Cisco 1700 Router. The connection is working and all workstations can access the Internet. NAT is configured on the router and an ACL is applied to the inside interface. I am experiencin...

Hi All..I have a router 2600 with the module NM-E3 ATM. This router is coneect withc cloud ATM. I can to configure this module to connect with WIC-1MFT-E1 with module AIM ? Or to configure this module with the bandiwdth 2MB E1..ThanksCassio Gomes

With regard to this config:*****************************************interface Serial0/0/0.16 point-to-point bandwidth 512 ip address 192.168.79.2 255.255.255.0 frame-relay interface-dlci 16 protocol ip 192.168.79.1 class test512*********************...

Configuration:R1-->ISP1R2-->ISP2R1<--iBGP/HSRP-->R2R1=HSRP Active routerIOS 12.2I have a case where I am advertising one /24 network via BGP to both ISP1 and ISP2. In an effort to resolve some asymmetric routing issues, I'd like to do the following:...

Does OSPF every 30 minutes to generate the LSA?I saw lot of the following info every 30 minutesBuild router LSA for area 0, router ID x.x.x.x, seq 0x800000FEthanks

Is there a proper way to query a router's interface for input errors? The only OID I could find for this was .1.3.6.1.2.1.2.2.1.14.n (with "n" being the interface to query), but when I do a "show interface..." the input errors don't match the number ...

I have found out that our 3885, won't play with 3662 due to IOS version differences, but i can't upgrade 3662, until i get rid of ACC router, as it can't due rip-2... question is this, whay can't stores that are connected to 3885 (which is in corpora...

I have a 1841 with IOS c1841-ipbase-mz.123-8.T7.bin,when I do a trace to an address that is not in the table it reply in the first hubMS1RTR01#traceProtocol [ip]:Target IP address: 198.133.219.25Source address:Numeric display [n]:Timeout in seconds [...

Hi ALL,This is in the lab for testingI have installed the Kiwi Syslog Daemon and now i want to get the log messages from cisco 7500 series router.I have configured the following in the routerRouter(config)#logging onRouter(config)#logging<serveripadd...

Can I do the compression like predictor or stacker on Cisco switch 4506 on Ethernet interface, If not then what is the alternative, If yes then can somebody please tell me the basic commands. Thanks,

Currently have a frame relay circuit on an end point terminating into a 2611.interface Serial0/0.....interface Serial0/0.101 point-to-pointip address 192.168.101.6 255.255.255.252frame-relay interface-dlci 101!If i add 2 new frame drops then I need t...