Hi all,I have an issue on IS-IS in vrf-lite.PE rotuer receive specific network and default from MP-BGP session with RR.There is a mutual redistribution between MP-BGP and IS-IS on VRF-OUTSIDE.On IS-IS process in VRF-OUTSIDE there is command to genera...
I hope this is the right place for me to post this question.I would like to know, if a router doesn't support VPN (meaning it can't be used as a VPN server) can it still route an IPsec packet? And which router I should use as a server for IPSec (AH t...
Hi, I have 2 sites which each have a pair of Cat9500-32C switches in virtual stackwise as core switches and are connected together with 1x 10G L2 and 2x 1G L2 fibre (essentially dark fibre) circuits. We have configured the links between the sites as...
Hi all.I am looking for some help with this, I have searched multiple threads and none make it clear exactly what needs to be done, or how to do it. Whilst below is a diagram does not tell the whole story. I need to create a GRE Tunnel. Please be aw...
Hi folks, I am currently working on obtaining my Routing and Switching qualification and thought I would replace my existing router with a Cisco 887VA. All was going well when the expected IP address was showing on the dialer interface and able to ...
Hello, i have two vlans, one is for internet operator (115), another is LAN (119).Provider give us addresses 1.1.1.24/29, 1.1.1.25 - providers gatewayWe have local host 192.168.46.2 in our LAN interface Port-channel1.115 encapsulation dot1Q 115 ip ...
Greetings everyone. I really need help here, I'm on my first IT job after getting my CCNA, but now I'm lost here. My employer needs to provide access to our internal server (located in Japan) to some staff located in an office in India, but only acce...
Hi,One of my ASR9001 consumes power only one side. While another load share normally. How should I do? Thank you very much.
Hi, I am trying to configure L2TP remote connection back to office, however when I try to add the crypto map to my interface i get "Cannot apply empty map to interface" what am I missing?R1(config)#intR1(config)#interface gig5R1(config-if)#cryR1(conf...
Saludos comunidad. Busco ayuda con un problema en nateo y salida a internet en CML. Tengo la topologia mostrada en la imagen. A l router ISP se crearon las listas de acceso con las redes de hogar y entre routers, se aplicaron a las interfaces las reg...
Hi GroupI'm having a Cisco ISR C1111-8P Dual GE WAN Ethernet Router in my organization today i am trying to make test speed to certain server the wan interface with the PE router is 1G also the Lan interface with my laptop is 1G directly connected ...
Hi Team, I would like to create an "object-group service" and would like to define only the destination ports as shown below. object-group service web-ports service-object tcp destination eq 80 service-object tcp destination eq 443But I do not g...
I'm in the process of migrating traffic from one provider to another. Currently, Provider A is set with a Local Pref of 200 and Provider B with a Local Pref of 100. Do BGP Local Preference changes take place immediately, over time, or does clear ip ...
Hi all,I've got an ISR4331 running 12.16.4 set up to be our office edge device running NAT overload to the ISP (using VRF-aware NAT) and ZBF inside-out with a match-any that includes UDP and ICMP (and other stuff above of course). It works perfectly ...
Hi, I have two BGPs configured on my core router. One is with P2P link to another location (site B). Other is with MPLS circuit which connects all other sites. Now, my routes from site B are being learnt from P2P bgp while of other sites from MPLS. T...
