I have a n9k switch where I have couple of vrf's like management,default,107,108 . Traffic is getting routed via management.I want to make 107 vrf accessible to outside network.I have very limited commands in management so can't leak routes.
Forum Posts
Greetings and thank you for your time, To summarize/simplify my issue, we have two ISP to which we need to conditionally advertise our public subnet to ISP 1 but not the ISP 2, unless ISP 1 is down. We don't want to use AS prepend to ISP 2, we simpl...
Hi master. I have router ASR9K with single ISP (ISP-A) using BGP routing. now, my company need to add new ISP (ISP-B) on Router. The ISP-B carry single ip neigbor (peering) with dual AS, for example AS-300 for Internasional (IIX) and AS-400 for (...
Hello, ASR 9006 High cpu usage on RSP1.Сan someone explain to me what the problem is?Thank you!sh logRP/0/RSP1/CPU0:Mar 6 12:16:23.394 : wdsysmon[446]: Process hd_drv pid 49186 prio 21 using 50 percent is the top user of CPURP/0/RSP1/CPU0:Mar 6 12:16...
This is how I do it on ASAobject network L2L_NAT_OVERLOAD_IP host 10.200.255.1object network L2L_NAT_DST subnet 172.1.1.0 255.255.255.0nat (INSIDE, OUTSIDE) source dynamic LAN_INTERNAL L2L_NAT_OVERLOAD_IP destination static L2L_NAT_DST L2L_NAT_DST th...
i can't ping from Admin to R1 or R2 or any of the endpoints connected to R1 but i am able to ping R3 from admin and then am able to ping the endpoints of R1 from the cli of R3 any ideas on what the issue is
Resolved! How is MPLS TE path weight calculated?
I'm trying to figure out how a TE Tunnel on Cisco IOS-XE gets its path weight value.R1#sh mpls traffic-eng tun tu100 Name: R1_t100 (Tunnel100) Destination: 3.3.3.3 Status: Admin: up Oper: up Path: valid ...
Whats up Cisco forum users, So i am experiencing something weird, basically when i mention the explicit-path in the segmented routed Tunnel (with the command 'path-option 10 explicit name path1 segment-routing' , for example) the Tunnel does not work...
Hi!I'm trying to opload a config file with txt extension to a ISR4321/K9 and router TFTP debug "TFTP: Sending error 2 Access denied". Is this is possible? 001392: Mar 4 10:09:22: TFTP: Server request for port 54576, socket_id 0x7FA143143B30 for proce...
Hi All, Currently entire network is under ospf area 0 with internet traffic in DC routed out to ISP 1, and DR internet traffic routed out to ISP2. We have a requirement to do a routing failover from DC to DR when Internet connectivity to ISP1 is down...
Hello, In out subnetwork we are using many internet lines and accessing these inernet lines reachability is controlled via cisco mac access-list which is configured and applied on the C3750 switch.everything was working perfectly with no prob...
I try to repost here one of my posts that found little response ... I need to extend some VLANs between two location (the Enterprise DataCenter and a remote DR DataCenter).The obvious solution is using OTV between two CSR1000v's.The connection I have...
Dear the Cisco Networking Community, I have just read the document: https://www.cisco.com/c/en/us/support/docs/ip/open-shortest-path-first-ospf/47862-ospfdb3.htmlI noticed that in Router 1.1.1.1, there is an entry 5.0.0.2/32 via 5.0.0.2. I am pretty ...
So if you want to reduce how much bandwidth can be used from certain hosts/subnets destined to one particular subnet, it would be best configure Layer 3 QOS correct?If let's say VRFs on a L2/3 switch are used for just the particular source subnets, d...
Resolved! Multiple BGP instances on n9k
Hello,In a lab setup, I want to set up 2 bgp instances in 2 vrfs to test eBGP feature among those 2 instances.I have one n9k is this possible to set up.How would I leak routes between 2 vrfs? Is it possible to have 2 AS numbers on the same n9k or do ...
