Hi Team, I am looking for some recommendation around 3750 and 4431 CPU or memory threshold value configuration. Each month we have a few switches and routers that operate above the configured high tide values, almost every time the Team investigate t...
Forum Posts
Hello,I have CISCO1941/K9 routers which are running version Version 15.7(3)M6 & only have a 4g cellular interface as a WAN link. The signal or link drops ever so often & doesn't connect unless a shut/no shut is done on the cell interface. When it dro...
Resolved! Inter-Vlan Routing not working
Hello, I have an issue getting inter-vlan routing working. Here's the setup: Switch 9318 - IOS 9.2(3) - License ACI EssentialsVlan4192.168.1.1no shut Vlan5no shut192.168.2.1 Ethernet 1/48Trunk to 9200 Switch 9200 - IOS 16.12.02 - License Network/DN...
i have this invalid vrid increasing with no clear reason #show vrrp interface TenGigE0/0/0/0.500 statisticsTue Oct 6 17:06:21.303 EGYTenGigE0/0/0/0.500Invalid packets:Invalid checksum: 0Unknown/unsupported versions: 0Invalid vrID: 4626Too short: 0Pr...
i have Cisco 3825, Cisco 7206 VXR and Cisco 1841 Routers ,so i need to replace them with other CISCO Models so i need recommendation for each Model replacement .
The ping command between Laptop0 and Laptop1 does not work either way.What is the cause? How would you resolve the problem? Please help me with this as soon as possible
Hello, I have some asymmetric routing happening with a partner organisation. We are running BGP into MPLS from 2 locations, I also have an internal network between my locations and I am running iBGP. I am advertising prefixes for both locations, a lo...
Hi AllI have some ACI questions. 1.Does the fabric always use vxlan?2.Do you have normal vlans on the leaf switches and then do these map to vxlans on the leaf? is this done automatically by ACI?2.What is the take up on aci these days? are many Nexus...
Is it possible to use DC power in cisco 4331 router? I found this article where is part about how to "Remove DC Input Power from Cisco 4331 ISR". Thank you for replies.
I have an internet facing Cisco 891F router that I have been requested to make some NTP changes on. The current and only NTP configuration has the router looking to 3 different public time servers.ntp server 1.1.1.1ntp server 2.2.2.2ntp server 3.3.3....
Hi Got an ASR 1002 running asr1000rp1-ipbasek9.02.06.02.122-33.XNF2.bin Getting this log filling up the router Apr 30 03:51:26 BST: %PLATFORM-4-ELEMENT_WARNING: R0/0: smand: ESP/0: Committed Memory value 304% exceeds warning level 300%*Apr 30 04:01:...
Resolved! Static Route update in EIGRP with IP SLA
I'm needing some configuration assistance/advice. Right now we have a remote site that's connected to our LAN via a full-mesh VPLS uplink and EIGRP configured between sites. The remote branch has its own ISP connection that we'd like to have as its ...
I'm needing some configuration assistance/advice. Right now we have a remote site that's connected to our LAN via full-mesh VPLS uplink and EIGRP configured between sites. The remote branch has its own ISP connection that we'd like to have as its pr...
Hello, I managed to back up the running config on a Cisco 2911 using tftp, the file is sitting on a Linux server.I can copy the file using tftp, from my workstation. So both writing to and reading from the tftp server is working. However, when I try ...
Greetings,I am looking for help with a sample configuration that will allow 80% bandwidth utilization for an application, and the rest of available bandwidth for all other traffic.Thank you
