Hello,I was experimenting with route-map with continue clause, however the use of continue clause does not set well with my understanding of its processing. 1. A route matches a match statement execute its configured set values and then jumps to ...
Hi all,I'm not that familiar with VOIP but we've got a client that has had a VOIP system and it goes out of a Cisco ISR4431 but they cannot do any internal transfers as they say the caller-id is translating to the WAN IP when it goes through the Cisc...
Is it possible to inject a static route from a router that is not configured for OSPF into a mesh network that is configured for OSPF and also send it back to that non-OSPF router via another static router. Basically it would be a totally stubby area...
what i mean about that lets say i have 192.168.0.0 and i need 200 sub-nets and 300 host each.by default this is a type c network with a /24 mask. is it possible to go backwards. to meet the demands. My second question is do you need a sub-net mask t...
Hi Dears.i have a P2P Wireless Link as WAN which has variable speed due to bad air condition( at offshore drilling rig). it's speed vary from 30mbps to 25 or maybe lower( it is not predictable). i have a Cisco router as gateway which uses this p2p wi...
Hi everyone, I am trying to get LTE running on ISR 11xx routers.Old config (dialer interface with "dialer pool" command and the cellular interface with "dialer pool-member" command) ist not working.As I read there is new way to configure that.That is...
1-Can we use int Mgmt Pot in Netflow instead of interface gig 1/0/0...? flow exporter EXPORTER-1destination 172.16.10.2transport udp 90exitflow record v4_r1match ipv4 protocolmatch ipv4 source addressmatch ipv4 destination addressmatch transport sou...
Hello all, I'm new to Networking and I'm a newbie in Automation. I am here to take suggestion from the experts to solve my issue We are having a SCADA PC which is placed in the headoffice and we have 50 sites.We needed to collect data from the PLC s ...
Hi anyoneI would like to know best parties design for normal area https://ibb.co/TBrzyQF Here's diagram to example I have two site A and B Router 1 and Router 2 as same area 1but Router 4 Area 2Router 5 Area 3Which one site is correct design for...
Hi all, I am unable to send packets from a PC to the routers.I am able to send a packet from the PC to the Su Zhou router but the routers beyond that I am unable to send any packets.Am I meant to configure a recursive static route/static between the ...
I have erased ios from serice module of router 2921. Then i was trying to upload ios using copy xmodem: flash:(file name) But it was taking much time. At this point Console clock rate was 9600 Line vty 67 BAUD 9600 SW BAUD 9600. Then unfortunately i ...
Dears , im sicking an exact information about the GRE tunnel capability from capacity point of view as i'm wondering about the maximum BW a GRE tunnel can support ( of course by using the correct hardware to support that )can we send up to 2 G or mo...
I have any question example configurevlan 1ip 192.168.1.1 255.255.255.0 when i ping form source vlan 1 to server 192.168.1.10 result is !!!!.!!.!!!.!!! and test ping other ip same subnet no problem such as 192.168.1.11 ,12 , 13 14...and then i ...
Im confused on the host bits and sub-net bits when trying to design a networks.1 can you have type c network go backwards for example 192.168.0.0and i need 300 hosts and 200 sub-nets. is it possible.2 do you need need a sub-net mask to find hosts an...
I'm working from home thx to Covid-19 and have come up against a config challenge. Have a DSL with 5 static IP's, currently only using 1. The gateway is configured to pass through so it does nothing except host the public IP's. The LAN side is a sing...
