Hi, I am running two OSPF routing process on the same router, one process towards core and receiving default route (110) from core and i am running another process in totally stub area which in turn generating default route (108) towards down net...
I have two ISR4331 with 25 LAN facing sub-interfaces on Gi0/0/2. They all have HSRP running. Most have HSRP authentication. I tried to add HSRP authentication to those that did not have it and I received the following error.%Warning : Interface MA...
Hi, I am studying BGP and came across the concept of iBGP full mesh. If I understand correctly, the need to use iBGP full mesh is to let the internal routers within the Autonomous System (AS) learn the best BGP routes. Also, there's a BGP rule which ...
We have three VSS-Cluster of two C6832-X-LE in production in the backbone of our WAN.The WAN lines, which interconnect three Backbone sites have capacities of 10 or 20 Gbit/s.The question is: Which is the maximum ip routing througput capacity of a Ca...
Hai experts!In my work, i have experience to config connecting branches offices to data center edge router via BGP (with Metro E and MPLS media). But i curious about how to connect dc edge router to branch router vice versa via internet. Any idea? Do...
Hello! I had an issue when I setup AnyConnect for a client on a FTD firewall using FMC. The issue was that their ISP is handing out static IP addresses to all their clients on a shared /23 network. I didn't specify no-proxy-arp, and after a few hours...
MFWS-ROUTER#show configUsing 2821 out of 262136 bytes!! Last configuration change at 17:01:04 BST Tue Jul 7 2020version 15.3service timestamps debug datetime msecservice timestamps log datetime msecno service password-encryption!hostname MFWS-ROUTER!...
I ran across a practice test question that asked which LISP elements are needed to to support LISP to non-LISP communication. Here are the answer choices: PETRPITRMRMSALT It stated that the correct answers included PETR and MR. However, shouldn't the...
I have BGP multi-path setup but only one router in AS65222 is receiving traffic for the prefix 192.0.2.254. Goal is to have traffic from cloud distributed between AS65222 routers to the anycast ip. Thoughts on what is going wrong here? Topology is: ...
Hello,I plan to change my BGP/OSPF ISP routers with 1001-X. I need your opinion ! I currently have 4 routers:Router1 = 1 x Full-view IPv4 and 1 x Full-view IPv6Router2 = 2 x Full-view IPv4 and 2 x Full-view IPv6 + IX (Peers and RS IPv4/IPv6)Router3 =...
Hello All, I have got Three Cisco Routers and Three Cisco SwitchesOne router is 2901 gigabitTwo routers are 1921 gigabit All three switches are Cisco 3650 Catalyst version 2seriesall int on routers have been alloted with Ip addresses. Let's just sti...
Hello, I'm a little foggy on the throughput license which up the throughput from 500Mbps to 1Gbps. Currently we have a L3 link to our other site which was just upgraded to 1Gbps. I know that to get that full gig speed I need to purchase the license...
Hi all, I read about cisco 3825 integrated service router, but I am not sure about it, can someone explain it please? Thank you
Under Cisco IOS I have the following: route-map RPA-SET-MED permit 10match ip address prefix-list RPA-HTC-DMZ-NETWORKSset metric 50set community 4771:120!route-map RPA-SET-MED permit 20set metric 300 Under IOS XR for an equivalent route-policy as per...
Hi,I have a question, is it better to put ip inspect firewall in on LAN interface or put it on interface facing internet with ip inspect firewall out?Thank you
