Buy or Renew
Buy or Renew

Routing

cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
Start a conversation

“Webinar

 
Labels

Forum Posts

Start a conversation

Resolved! SR-TE XRv9k v7.0.1 "show segment-routing traffic-eng ipv4 topology" irresponsive also Dynamic SR-TE not working

Platform (XRv9k)Release (7.0.1)Input details or justificationDynamic SR-TE not working also "show segment-routing traffic-eng ipv4 topology" commands are irresponsive.(xtc_show process)also PCEP process and session not working.ipv4 unnumbered mpls tr...

alibia2 by • Level 1
  • 726 Views
  • 1 replies
  • 0 Helpful votes

Resolved! Router configuration to connect separate LANs

Hi,I am trying to use a Cisco 1841 router to make a connection between two separate LANs which are directly connected. FastEthernet 0/0 is connected to network 10.80.1.0/24 and the interface received IP 10.80.1.135 IP via DHCP from a router on this n...

ramram by • Level 1
  • 1002 Views
  • 3 replies
  • 0 Helpful votes

Multicast across BGP AS

Hello Experts,   I was configuring an INE full scale lab for the CCIE preparation and I faced the following problem with Multicast.   The idea is to have multicast traffic being R3 the source, R9 the receiver and R7 the RP. The ISP (R4, R5) are not m...

jgomezve by • Cisco Employee
  • 1073 Views
  • 2 replies
  • 0 Helpful votes

mfib debug output on C9K

Hi Everyone after migration to new core on C9500 series i've discovered some multicast blackholing between VRFs connected with GRE Tunnels on the same box. 'debug ip mfib vrf vrf-red 239.255.255.250' hints with bodled textDec 23 19:45:19: MFIBv4(0x5)...

Resolved! L2 Bridging Across an L3 Network Internet?

Is it possible to extend vLANs  over the internet to another site using a 3900 router on one side and ISR4321 on the other side with Layer 2 Tunneling Protocol Version 3 (L2TPv3) and Generic Routing Encapsulation (GRE)? Has anyone done this? Is it se...

hmc250000 by • Level 1
  • 1508 Views
  • 4 replies
  • 0 Helpful votes

Adding access-list 52 permit 10.50.1.2

Hi, How can I add another access-list 52 permit 10.50.1.2? Access rule can't be configured at higher sequence num as it is part of the existing rule at sequence num 50access-list 52 permit 172.10.4.1access-list 52 permit 10.50.1.0 0.0.0.255

getaway51 by • Level 2
  • 1649 Views
  • 10 replies
  • 0 Helpful votes

Resolved! APN inactive after rebooting the router c1111

I have configured the c1111 router with 4g Sim with  ANP provided from my service provider.after configuring the profile,APN will  active and we can use the internet from the LAN network. but when I reboot the router and its come up with all configur...

Resolved! Network and Vlan no internet

Hello Everyone!Merry Christmas  !!!This will be my first post here and I bit exacted . I am kind of beginner in Cisco networking. I am trying to build something as Soho network. I have a problem with topology  and I can not find where is my wrong.I c...

Resolved! Committed Memory value %

Hello colleagues, How's going work?Recently my ISR4331/K9 started to be a little bit buggy. It uses IOS XE version 03.15.00.S. and IOS Software Version 15.5(2)S. It so much slow that I am unable to type commands. I have all logs from device but I am ...

ip_guy by • Level 1
  • 4658 Views
  • 11 replies
  • 0 Helpful votes

Resolved! Network Configuration Help.

Good afternoon Team, Long story short, I've had to move a my server to my outside closet where my 3945e is located. Now in my living room I have my main switch setup (4948), and I used to have it connected to that, so I thought "Well since I don't ha...

RBM01991 by • Level 1
  • 1402 Views
  • 5 replies
  • 0 Helpful votes
View All
Unanswered Topics
View All
Review Cisco Networking for a $25 gift card