Hi Guys,I need to convert layer 3 interface to layer 2 in a 3750 switch. That is I have a packet shapping device which work on layer 2 and all the packet from inside interface of PIX need to be pass via the packet shapping device so that it can log a...
Forum Posts
Resolved! 3750 IOS upgrade failure
Hi,I'm trying to upgrade a 3750-24TS from c3750-ipservices-mz.122-25.SEE2 to a more recent image.On the first pass, I gotError: There is insufficient space in flash: to install the requiredError: image. Clean up some old images, and try again.So I u...
Resolved! Routing problems on 1100 Isr
Hi,I'm a newbie trying to configure my new Cisco isr C1113-8p for my network.I set up my running-config and my router can navigate, but I'm getting some strange behaviours... and I'm sure they're related to something wrong on my routing configuration...
Resolved! NAT & Routing
I been using static nat and has been cumbersome to manage. For example I will do a /24 static nat to make all the NATs are known for monitoring. Question came up that can we NAT a subnet and they will always line up with last octet the sameexampleip ...
I've been looking into this as we're getting very close to the new Cisco exams and it seems to be accurate, but I can't be sure because I didn't find the official information to confirm it.. I want to complete both CCIE R&S Written and CCNP TSHOOT a...
Hello First I am unsure if this would be under Routing or Switching so I do apologize.I currently am using an ASA-5508-X with a block of 8 (5 usable) Statics. Of the 8 usable Interfaces on the Router and 1 being Input (Internet) and 1 being for my AS...
Hello,I am currently using some of my lab equipment for my Routing and Switching studies where I have built a VPN to my woodshop. At home I use a Cisco 2911 router and at the shop I have a 2800 series router. I had everything running good for about a...
Resolved! Links not turning green/Pinging issue
Hi all, hope you have a good day :) So I am trying to set up a simple DSL network with ISP. I was following the instructions of setting it up by watching some tutorials on Youtube since I am still a beginner and still learning networking. I did the e...
Hi,we are operating in Germany, and for a couple months now problems have occurred, most likely after some changes on the DSLAM side of the links.We typically use 886VA routers, which work fine. But in some cases, either a firewall with direct PPPoE ...
Resolved! Routing Switch L3
Hello guys!I have few questions about routing Layer 3 switch. On some point going lost and I do not know how that happened.When use switch L3 connect the router I think need to be -No switchport – why?? I know the no switchport working as L3 routing....
Dear Folks, I am studying the CBT Nuggets Keith Barker MPLS Fundamentals videos. While i am studying the redistribution lecture, i am not understood what is asked on below yellow highlighted question and whats its answer. Kindly help me to understand...
Hello everyone, I need to configure fcip tunnels between 2 MDS 9250i, but I have some doubts.Each device has 2 FCIP interfaces, and it has been decided to assign 4 IP addresses to each device, (2x IPs per fcip interface), don´t ask me why, someone de...
Hello. I would be grateful for any input/help. Please see the attached diagram. Bottom two Nexus are in Site 1 and top 2 nexus are in site 2. (Please ignore the L3 links between N1-N2 and N3-N4) 10.17.13.10 is dual connected to both Nexus. We run HSR...
Hi, I am having issues with a 5508 ASA with policy based routing. I setup PBR rule that forwards traffic towards another network and away from my default route. This PBR directs ICMP and HTTP away from the normal network out to another network.ICMP w...
Hi, Just got an RV345 today :D, how do i check the router load whether the router already overload or not ? Thank you
