Routing

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
Labels

Forum Posts

waas express license

Hi friends I want to run waas express in 2901 router, but I encounter a problem with license. when I use "show license detail WAAS_Express" command, the result shows that, this feature is not exit. I used this show command in 2921 and see the the lic...

Resolved! source and destination ip address

hi  need to know whats the source and destination ip address like below schedule  that i have to fill    Access rules Source IP Dest IP Destination protocol & port Application used Comments                                     ...

amralrazzaz by Contributor
  • 18741 Views
  • 10 replies
  • 0 Helpful votes

Resolved! problem with LDP and CoPP

hi here i've issue with control plane policy on AS1001.i configured follow statement:   class-map match-all MGMT match access-group name MGMT class-map match-all ICMP match access-group name ICMP class-map match-all ANY_TRAFF match access-group na...

unfraget1 by Beginner
  • 2239 Views
  • 18 replies
  • 0 Helpful votes

Resolved! Why CEF needed in MPLS Network??

I have read the MPLS Fundamentals book by Luc De Ghein, So I understand from the from book that cef needs to enabled in edge routers to tag or untag labels (for Ip packets). I am eager to know why Mpls (Not a cisco proprietary) depends on a cisco pro...

bava_ccna by Beginner
  • 9900 Views
  • 6 replies
  • 0 Helpful votes

Internal Error for ip sla

We have 7200 series router to calculate the ip sla. One of the ip sla probe statistics  is showing as Internal Error and there are no successful operations for that specific probe. There are other probes on the same router which are working fine. xxx...

Upgrading IOS for Cisco 1001-x

  Hi all,   I am trying to upgrade the IOS for Cisco 1001-x from 03.x to Everest 16.6.4 and I believe I need to upgrade the ROMMON version as well, but however I don't see ROMMON software available for 16.6 as it has to be the same IOS if I am upgrad...

krisvamcee by Beginner
  • 2382 Views
  • 19 replies
  • 0 Helpful votes

No Service-module command

Hi everyone,   I need some help, my client just bought cisco 4331 and want to use voicemail. I've read about this in some articles, they said in 4331 voicemail use service engine interface for CUE. In my 4331 router, there is serviceengine0/4/0 inter...

2018-01-10_111016.png 2018-01-10_111101.png

Resolved! IPv6 RP questions

  Based on my understanding of IPv4 multicast, if I join a group on the receiver, RP will show a (*,G) tree. When I configured via the following command interface Loopback1 no ip address ipv6 enable ipv6 mld join-group FF0E::1 ipv6 mld join-group FF...

IPv6 Mroute.JPG
gongya001 by Beginner
  • 580 Views
  • 9 replies
  • 0 Helpful votes

Resolved! Rib Failure BGP

Will a iBGP speaker advertise a prefix that is a rib-failure? I have a particular prefix where all its paths are rib-failures and it is not advertising to any of my iBGP peers.      

Resolved! TAC support responsibilites

I am wondering if you can please answer this. So you ask a Cisco TAC for an advise/best practices on let say routing. You ask them their view on for example routing specific network in a specific way. You are wondering if you are doing it right or wr...

sheahm by Beginner
  • 739 Views
  • 3 replies
  • 0 Helpful votes

Resolved! BGP not Advertising between Neighbors

Routes in route table not sent to bgp peer at 10.0.79.70 but only two subnets sent. Need to send them all including default route.   <hostname removed>#sh ip bgp nei 10.0.79.70  advBGP table version is 1840, local router ID is 172.16.159.17Status cod...

haydavis by Beginner
  • 2362 Views
  • 15 replies
  • 0 Helpful votes