I've seen on places organisations using 10.0.0.0 Address class for VPNs & Intranet, Can anyone guide me why use this particular class??
I've seen on places organisations using 10.0.0.0 Address class for VPNs & Intranet, Can anyone guide me why use this particular class??
Hi GUYS Pls find attachment why we need such Config , pls clarify thanks
Hi Folks, I am facing an issue regarding the connectivity of Gateway to Gateway Site VPN in RV042 and RV042G Router. I did configuration as per https://www.cisco.com/c/en/us/support/docs/smb/routers/cisco-rv-series-small-business-routers/smb3294-conf...
One of my customers is looking for an xlsx version of the log messages found in the following: For IOS devices: https://www.cisco.com/c/en/us/td/docs/ios/15_0sy/system/messages/15sysmg.pdf For IOS-XE devices: https://www.cisco.com/c/en/us/td/docs...
Hi we have a requirement to restrict the bandwidth on the 10G link as it will be split in to two sub interfaces with one set to use 40% and the other of 60 % of the bandwidth. But wanted some pointers of how to do it and how to calculate the burst ra...
Hello, I have an MPLS connection between sites and I need to measure the bandwidth capacity of the MPLS links. How can I do it? I have Catalyst switch 3750 and 3850.
Hello, The A9K-24X10GE-1G-TR LC datasheet has an explanation as below. Can someone explain this a bit?- The throughput is 200G (I think there are 2 x 100G conenction at backplane), and how can it operate up to 240G ? https://www.cisco.com/c/en/us/pro...
To all Cisco enthusiasts, I am looking for a documentation about this matter I run into. How come that I can not change the queue-limit in any of my Qos Classes to use byte based queue calculation and not packet based. on ASR1001-X I can set Pack...
Hello There, We are currently having multiple issue with a SLA. There are random failure.This SLA is a basic http get to a ressource from internet.We are monitoring this ressource on different VRF by different DMZ.It appears that from one specific vr...
router bgp 67111bgp router-id 1.1.1.1bgp log-neighbor-changesno bgp default ipv4-unicastneighbor EBGP peer-groupneighbor EBGP remote-as 67222neighbor 192.168.1.61 peer-group EBGPneighbor 192.168.1.65 peer-group EBGPaddress-family ipv4redistribute osp...
We have a client we need to establish a S2S IPSEC tunnel with, it also requires source NAT from an IP they specified (not within the remote host subnet ranges.) Site A (Our Site):Local Subnet: 10.252.0.0/16WAN IP: 1.1.1.1 Site B (Client Site):WAN IP:...
Hello all,I'm looking to tap in to the experience of the community here at a design level. We currently have 20+ remotes sites connected via DMVPN over internet through a handful of different ISPs. All sites are given a static IP from their respectiv...
We have approximately 20 remote sites running DMVPN in a typical hub and spoke configuration. Hub is a 4431 and spokes are 4331s. We have recently moved web filtering to a centralized appliance at our data center and, as such, I need to backhaul inte...
please remove this post.
What is the command to find out the backup path for a route in OSPF when the primary path is active. The show ip route is diplaying only the active path and the show ip ospf database is also showing the advertised-router which is active at the other ...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
08-07-2024 10:40 AM | ||
07-15-2024 05:07 AM | ||
07-13-2024 09:04 AM | ||
07-09-2024 05:41 AM | ||
07-03-2024 08:54 PM |
User | Count |
---|---|
12 | |
9 | |
8 | |
5 | |
4 |