Hope some can assist, all my traffic hung on my router, this is a debug all after the hang and during a reload. bifrost-cisco2951#Aug 26 19:06:55.378: %OIR-6-INSCARD: Card inserted in slot 1, interfaces administratively shut downAug 26 19:06:55.390: ...
Forum Posts
Hello guys,I am a little confused about weight and MED bgp atributes , so far I know the following: - Weitght is just used by Cisco products- MED is the sixth tie breaker and the weight the 1st one- Both influence the router to reach and specific pre...
Hi EveryoneWe run a small Wireless ISP and due to our grow we are setting up our network for full availability for our customers. We got our AS and IP block from ARIN, and we have internal OSPF for all our POPs, we have 2 Internet upstreams with sam...
Resolved! ISR 900 Series
Dears, I m trying to choose between C921-4P and C931-4P can i know the difference between them hence i am not getting in the datasheet any difference, where i can find the throughput for these routers, also i want to know the 4 ports LAN switch po...
Hi folks, I have connected a Cisco ASR 1002 router via a sub-Int gi0/0/1.1 [has an IP] to a Cisco 3750G switch. vlan id and dot1q taggs are in place under sub-int and port on switch gi1/0/25 (the uplink) is trunk. the switch port is not connecting. t...
Resolved! basic distribute-list with access-list
so as a 'youthful' netadmin looking to expand what I know, I'm reading CCNP routing content & going through some review questions. in using a distribute-list to refer to an access list, does the implied "deny any any" at the end of an access list st...
Resolved! Loading Balancing on Cisco IOS
Hi!Can anyone explain to me how do cisco devices router or switched do load balancing of bundled interfaces (bunde-ether,port-channel)?
I just took and passed the 300-115 SWITCH exam yesterday to re certify my CCNP R&S (also my CCNA and CCNA Wireless). I was thinking of working towards the CCNP Wireless next, or doing CCNA Voice -> CCNP Voice. Would I be better off going for this new...
Resolved! How can Cisco 4500X send IGMP join message to the multicast source without high CPU usage?
Our multicast service provider need IGMP join packet in order to send the multicast traffic. The service provider does not support PIM routing. We have a Cisco 4500X switch between the multicast service provider and the multicast receiver. If I set o...
Good day, I have a Cisco 881 router which was working fine until one morning after trying to start up all the LEDs on the router came on and won't go off. I left it for hours yet the LEDs didn't go out and trying to log in using a console cable, not...
Hello!My friend have a Cisco 881 SEC NPEthey buyed license SL-880-AIS and try to activate and get error:#license install flash:2045-ru-nov01_28082019_FCZ1607936T_20190827080858.lic.xmlInstalling licenses from ''flash:2045-ru-nov01_28082019_FCZ1607936...
Resolved! 2921 Compatible DAC SFP Cable
Does anyone know if there are third party SFP DAC cables that work with the 2921 router? The 10gtek SFP+ cables claim to work with Cisco, I just dont want to buy something that wont work in the SFP port on my router. THANKS!
Hi all,I want to use MSDP to exchange multicast sources between different customer network domains where no BGP is used but OSFP.Each domain uses it's own two rp for redundancy with anycast rp (without msdp meshgroups). Multicast routing protocol is ...
What is the use of command load-interal 30 on Cisco router interface & how this is helping to load share along with Bandwidth cmd.Ex:-On Router 1Interface gi 0/0/1description Connected to DC router1Bandwidth 46080Ip address 192.168.1.1 255.255.255.25...
Hello,I have configured ssh on 2 cisco routers in one branch. Both of them was working fine but one day suddenly one of the router's ssh stopped working. Now when i try to access by putty, immediately it gives me error message "Server unexpectedly cl...
