Hi All, Recently purchased an ASA 5508-X w/ FTD. I'm trying to configure a flat network for it, but it seems to not be able to route out. I created the route rule and set the gateway in the WEB GUI but it doesn't seem like it'll stick? Here's a clean...
Hello, I have a problem with Cisco ASR-920-24SZ-IM, when I plugged the power cord to the router, the console shows up in this mode, which has only a few commands. I tried to boot the system, but the result is as in the following picturesI have tried...
Hi,I have a basic set up that does not seem to be working as expected.this is all physical set up which consist of:Cisco Router - 1900Switch - 2960-X2 Win 10 MachinesSet up:Router 1 - Fast0/0 - Ip 192.168.1.4 / 24 VLAN 99 - DG Ip 192.168.1.4PC 1 - 19...
I'm trying to send syslog to a syslog-server through an L2L ipsec tunnel. The tunnel is up but the logging host does not work. I've done a tcpdump on the syslog-server and don't see any messages coming from the remote peer. The full configuration fo...
On the Nexus 9k, the only MTU's are 1500 or 9216. The 4500-X supports a range from 1500 to 9170. OSPF especially is very sensitive to MTU mismatches. Does this mean that you cannot use jumbo frames between a Nexus and 4500-X switch, especially if ...
I set my Linux server to ping the remote PC (over an IPSEC L2L tunnel) every 600 seconds overnight. When I return in the morning the ping is stalled and will not restart. There is no log entry for denial in the logs. Bouncing the remote INSIDE-IN ...
Hi all, I would like to confirm that A9K-MOD160-TR is compatible with ASR9006. It seems that it has on the rear right side some connectors missing from the backplane of ASR9006. Thanks in advance.
Hi Freinds Any Special Design/config to designate ASR 9010 as BNG Node thanks
Hello , Kindly we have BGP working As Active/Standby for 2 lines From One ISP we need to Change it to be Active/ActiveR1 > ISP-R1R2 > ISP-R2 R1 Configuration for BGP As the following !router bgp 65500bgp log-neighbor-changesnetwork 10.260.260.0 mask ...
Hi All, if you are a current CCNP R&S and will expire before Feb 2020: Can we take any of the CCNP exams (i.e. TSHOOT, Switch or Route or any CCNP wireless exams) to renew my current CCNP R&S and this will be migrated to the new CCNP Enterprise for t...
Has anyone had success with managing remote ENCS 's with DNA Center? I have been having a heck of a time getting mine to work. Right now I have a device sitting behind a PAT out to the internet. I am using the devices as it is right out of the...
What is the proper mtu setting for an MPLS interface on the 9400 to allow full 1500 frame from SVI over the MPLS? It seems to have changed from older IOS on the 6500/6800 to IOS XE16.6 to 16.9. Previously with on a 6500/6800 chassis we used "mtu 1...
My ISP mistakenly gave me a duplicate ASN for one of my sites. So 2 sites have the same ASN - lets say 45009. One site should be 45010 and the other 45009. THe ISP has assigned me the new number but wants to schedule a "cutover"...
Hello all! Recently, our network admin of 23 years left the employment of the business I work for. As a result, I am tasked with connecting an off site location to our network via a 4G/LTE aircard provisioned on our Verizon private network build out....
I have a CSR 1000V in two separate AWS VPC's. I have an ipsec tunnel configured between them. I have a linux host on each end and have been using iperf3 to test network performance. If I specify one udp stream with iperf3 I can max out the throughput...
