Hello,I have a question regarding the Cisco C8300-2N2S-6T.We are looking for the details of the ground lug and screw for the Cisco C8300-2N2S-6T. We use this information in case we lose the grounding lug and screws.Thanks,Will Salzbrener
The content you are looking for has been archived. View related content below.
Hello,I have a question regarding the Cisco C8300-2N2S-6T.We are looking for the details of the ground lug and screw for the Cisco C8300-2N2S-6T. We use this information in case we lose the grounding lug and screws.Thanks,Will Salzbrener
Hello All-I am reviewing a new campus VXLAN deployment. The one thing always confuses me is the required MTU configuration across all the new switches.Currently I see on all switches following configured "system mtu 9198". However at the same time si...
Hi allmy cisco Router C1113-8p has some issue. I had another Cisco router (1921 series) with similar configuration working mainly on the Nat and Dialler and was working succesfully.I had set up 2 Dialler to my ISP one for VOIP and the other for inter...
Hello, We are trying to upgrade our Internet speed from 100Mbps to 1Gbps. We were offered a fantastic deal through AT&T ADI fiber option. We currently have 2 x ISR4331 routers with the default license. We are advised by a consultant to get the Boost ...
We are in the process of migrating our remote sites to OSPF. We have two main head quarter sites connected by a 20 GIG point to point connection. The two main head quarters are our backbone area 0. We have approximately 200 remote sites that have dua...
I have a registered version of packet tracer 6.2.0 that I downloaded from the Cisco network academy web site. It is constantly crashing on three different computers. Can someone please tell me how I can capture the crash dump file so I can add it to ...
Hello everyone,Has anyone here tried using the SCADA feature on the IR1101?According to the documentation, it should be able to perform protocol conversion between IEC 60870-5-101 and IEC 60870-5-104 (in both directions).I’ve been trying to configure...
Hello and good day community, I would need your help with an DHCP relay problem on a Cisco C1131X-8PLTEPWE with 5G WAN connection. Let me inform you, before I tell you my problem, I´ve got the same setup, also with the same Vlan confiuration and same...
Hi All, Within my company we tunnel Async traffic over SSH between locations for Legacy low speed applications. At the moment we have 4000 series routers with NIM-24 Async modules that connect to the host system and Cisco routers 881v and Cisco 4321 ...
Hello all,We can of course use IP SLA's and Track objects to track reachability of a next-hop (like an ISP) and then remove a route to affect our routing, but I'm trying to think of an actual use-case where I would actually do this, as opposed to jus...
So I tried to upgrade from isr4400-universalk9.17.12.04b.SPA.bin to isr4400-universalk9.17.12.05a.SPA.bin. After the upgrade it will not register with my SIP provider. I see this. Aug 11 02:08:22.843: %SIP-3-REG_INTERNAL: Registration failed. Tenant=...
Hi,I've been doing BGP multipath labs and it seem that step 8, lowest IGP metric to the next hop, is skipped when you are using multipath eibgp.For example, R8 (below) has two neighbours - 9.9.9.9 which is iBGP, and 11.11.11.11 is eBGP:R8#sh run | s ...
on Data center router ,we have 6 VRF and let say we have subnet 10.x.x.x/18 and this subnet route is seen in all 6 vrf on that Data center routeris it possible ?as i learnt that VRF creates separate routing table then how can we see one subnet rout...
router bgp 100bgp log-neighbor-changesneighbor 192.168.1.1 remote-as 200neighbor 192.168.1.1 des R1neighbor 192.168.1.1 default-originate!R1ip prefix-list DEFAULT seq 5 permit 0.0.0.0/0!route-map RM_DEFAULT permit 10match ip address prefix-list DEFAU...
Use Space Bar to simulate Break Key Sequence Read this article if you are trying to generate a Break Key Sequence to access ROMmon, and the Break Key sequence does NOT seem to make it to the router.Today, I needed to access ROMmon on an IR1101 Indust...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
10-10-2025 02:07 PM | ||
10-07-2025 07:53 AM | ||
10-05-2025 07:46 AM | ||
10-05-2025 07:44 AM | ||
10-04-2025 05:41 AM |
User | Count |
---|---|
6 | |
2 | |
1 | |
1 | |
1 |