We recently announced the release of our self-serve virtual assistant. You can read the full announcement here. Videos and documents are available within a click for our latest products. Once you've told the bot what device you're using, the context ...
Forum Posts
(Updated September 2023 - Added Catalyst 1200 and Catalyst 1300 ) Hello! This sticky-post will serve as a sign-post for incoming community members. Below you will find links to pages that you may find helpful. Catalyst 1200 & 1300 Hardware Install...
Hi I have a SG500-24 port switch. To use this switch, i need to set system mode to L2 . Currently, it is showing as L3 mode. Logging into the switch, I noticed that the GUI is grey out for the set mode L2 or L3. Currently, the radio button is on L3....
Configuration file is also attached with queryI am having problem when configuring Voice and data Vlan on a single port.What I am doing that when we configure the below commands it works fine.VLAN for Voice is 20VLAN for Data is 24SVIs are configure...
I have a SG-300 (28) port managed switch,From past 1 week it has problems with internet as not of the ports are being connected ,the light blows for a minute and then goes off.Please help me out with this problem. how can i replace the switch and wha...
I have several SG300-28 and 52 switches. I have three new switches that I'm adding to the network. Each switch has several VLANS which are the same on all switches. When I have a computer on a port that has vlan 151 as 151UP I'm unable to ping the ne...
Hi, we use two SG350XG-24F as a Stack as core switches and 3 SG350XG-48T as access switches.The stack members are connected on fiber ports 23 and 24. Each access switch is connected via DAC to each stack member. No LAG there.We only created a LAG on...
Dear Community, We upgraded our RV340 yesterday to the latest firmware using 'cisco.com' as source. After this the router forgot all of its previous settings despite that we saved the 'running' configuration to 'startup'. We reconfigured everything m...
Resolved! SF220: Trunk between two switches
SG350 connected by fiber to SW3 port Gi1SW3 port Gi2 connected by cooper to SW2 port Gi2 in trunk modeIn SW2 Port 18 connected PC.PC cannot obtain DHCP, cannot ping any host, paket statistics show 0 packet recieved.When i telnet to SW2 then can ping...
I have 3 switches, 1 set to core switches with dhcp server and all vlan, the other 2 switches are connected to this core switch via trunk and get all the vlan from the core switch, vlan as below Core SW - VLAN 11, VLAN 13, VLAN 21 and VLAN 888SW1 - ...
Resolved! SF220: VLAN was not created by user
Good day!Before work with catalyst series and dont understand whats wrong.Have SG350-10SFP as router, in port GI1 connected SF220-24.At SF220 do:QC-NOPOE#sh vlan VID | VLAN Name | Untagged Ports | Tagged Ports ...
Hello All, A few months ago we installed a brand new SG220-26Ports switch. We did not change anything else at all in our setup (so no changes in clients or servers at all). But we notice since that moment, when a desktop hasn't been used for a while...
I have setup DHCP server on the PC which connected to SG220-50 Hub and two DHCP/BOOTP client also connected to SG220-50. The client send DHCP / BOOTP request packet continuously but the DHCP server never got the DHCP / BOOTP request. I changed SG220-...
Hi, I'm having issue to interconnect Cisco SG350 (Gigabit Managed SFP Switch) with 2960 switch. I used 100FX SFP also, not nothing worked.Looking very positive for any solution for this. RegardsReza Mohammad
After updating sg550x to new firmware it is continiosly restarting not able to access even by console just after login in few seconds it get restart. Hardware reset button also look like broken pressing with any wire nothing happen its gets inside fr...
Hi, I recently replaced my core SG500X switch by a SG350X 48P & SG350XG 2F10 stack (recent firmware). After a while I found a lot of issues, because of the unstable ARP operation of the switch. Sometimes the ARPs to remote devices (one more switch ...
