Hi All,
After creating the nve1 interface
!Command: show running-config interface nve1!Time: Thu Nov 23 11:03:16 2017
version 7.3(0)N1(1)
interface nve1 no shutdown description F: Network Virtualization Endpoint Interface source-interface loopb...
Hi,
I recently deployed a new version of DCNM and no longer have access to Fabric Manager, I see the functionality is now rolled up into DCNM. However, when I log into it I see none of my aliases have come in.
When I go to Configure - > SAN -> De...
Hi All
I am facing issues in find the nve1 interface.
for example i am trying to track the mac address of one server
sh mac address-table | include e8d5* 206 0050.56a4.e8d5 dynamic 0 F F nve1/10.93.64.10
But I am not able to track. I want t...
For Windows Serversfor qlogic qmi 3572/3472 -all the drivers versions areeither 9.1.9.25 ,9.1.8.6,9.1.11.26,QMI3472 - 9.1.9.25and few are fc version 5.09.00(90d5) driver ver 1.0.12.0are all these are compatible with cisco NX 6.3.2 ??On AIXVersion PCI...
When I try using plink to execute switchport description commands I am having a problem
interface fc1/9 ; switchport description Server_1 ;interface fc1/10 ;switchport description Server_2 ;EXIT
results in the port description for fc1/9 being cha...
Hello!
Im trying to connect MDS 9148 to existing fabric. I have an issue with one of vsan (31). All other vsan work fine. Ports for vsan 31 are in Isolated state. I see a reason of this behavior: Isolation due to domain not allowed. But I don't under...
Hello All,
I am booting UCS-B blades from the external storage but 1 blade out of 8 fails. I got it logged to the fabric (as well as the target). Also I have default-zone permit for these VSANs on both fabrics A/B. When I check on the adapter level...
Hi everyone, I know there are some topics about Jumbo but not with iSCSI.
My goal is to enable jumbo frame support on my Nexus 5624Q (I will receive them soon) only for iSCSI traffic.
I'm not sure about the config (especially because I don't have t...
Hi,
Is there a way to show from the CLI whether the switch is a 5548P or 5548UP ?
I have seen the physical labeling but wanted to a way to verify via the CLI.
Hi guys, First time poster, just have a couple of questions if anyone has the time and/or inclination. 1. Someone has previously created zones containing both a single hosts plain pwwn and also the alias'd pwwn. I'm pretty it wont but can someone con...
Hi
With SP created 4 vNICs to be used with Microsoft Hyper V and assigned the VLANs. We assigned IP to one of the interfaces, but failed to access the network. Later made the VLAN assigned to the vNIC as native VLAN through the SP, but still failed...
Hi
As of now we are using zoning with single initiator and multiple targets. We have both Dell Compellent and EMC SAN. With Compellent we are using virtual interfaces against each physical ports / wwns and DELL recommended to use all four virtual i...
Hi
We have configured 2 VSAN IDs (the default 1 with FC Port Channel and another one 3830 with FC uplink interface 1/26) with UCS (6248 FI in End Host mode, B 200 M4 blade, NPIV is enabled with MDS 9148S). Still the infra is not in production and u...
We are looking for the normal procedure in associating a service profile to a server / server pool. We created service profile templates and associated with server pool, but it's not creating the SP, so for testing we created a SP from this template ...
Hi
We used to do the zoning the traditional way and not sure whether to go with Enhanced zoning, if we go with enhanced zoning will there be any advantage and also is there any drawback. We have only a few zones (less than 100, used single initiato...