Hi,
Could any one help me that equivalent command to “service unsupported-transceiver” in 5548 switch.
My switch version.
kickstart: version 5.2(1)N1(7)system: version 5.2(1)N1(7)
Thanks,
hello,
I have problem with my server Cisco UCS C220 M3S with SD card
I want install windows Server 2012 R2.
so if I use the os install DVD no see my SD card.
If use SCU iso en use menu "OS install" have message :
"Warning : OS installation can not ...
Hi ,
We are getting frequent discards on Netapp filers connected on nexus 7k ,Following is the observation at our end .
1 flow control is disabled .
2. No jumbo frames enabled .
3. No Cos enabled for iScsi traffic .
What could be reason for these ...
Hello,
I have to remote sites connected via Dark Fiber, this 2 sites are connected to EMC / VPLEX. Because of the EMC requested I have only 1 vsan for the 2 sites.
At this point in site A I have already added my active zoneset, I just connected the...
I am looking to remove the first switch in the fabric, this switch is the principal switch at the moment, I have found the commands to change the switch priority but am looking for some guidance on if this process is disruptive to the fabric traffic?
Hi,
I have a MDS 9148s configured with NPIV, all my ports are connected to EMC, my question is,, one of the ports is set in FL mode automatically.
And I don’t understand why this is happening?
Thanks. all
323
I can't find a clear answer on FCoE traffic load balancing on 7k storage VDC. The following Cisco 7k FCoE reference has obvious configuration mistakes in load-balancing configuration: http://www.cisco.com/en/US/products/ps9670/products_configuration_...
Hi all,
We have a Fabric with four Cisco switches. For a new project based on Redhat Cluster, we are planning to use the Cisco MDS 9148 switches as our fencing device. The snmp user(in switch) will be used in shutting down the ports where the server...
Hi all,
I have 2 9148s, they are connected via TE ports, I have to create zones/zonesets for the same vsan, but I would like to know, i there’s any way I can create a zone/zoneset in one of the 9148, this can be replicated to the other one?
thanks....
I am trying to find information on connecting my 5672UPs to the HP 8/24 San Switch via native Fiber Channel. All zoning will be done on the HPs. The 5Ks will be used to connect multiple SANs (along with 77Ks) via IVR...
I understand there are a ...
Hello,
At our DR site we have not purchased a Director Class switch for our environment. Instead, we have purchased two pairs(4) of MDS 9148s for our arrays, servers, data domain, etc.
The configuration would be two fabrics, 1 pair for VSAN 100 fabr...
Hi
I have cisco MDS 9509 ("Supervisor/Fabric-2") running version version 3.3(5b)
In order to ugrade the OS to 4.2.9 i had replaced existing IP Storage Services Module DS-X9308-SMIP has been repalced with 4x1GE IPS, 18x1/2/4Gbps FC Module DS-X9304-1...
I have a 9216i’s (nxos 4.2) and a 6120 (ucs 2.0) that I am trying to configure a san-port-channel to port-channel with and I can’t get it working. The FC (F-NP) links work when they are not in a po, but when I try to form a port-channel I get “invali...
Hi ,
My Name is Bhavesh. I have installed the new Cisco UCS CPS 2ru k9 server and after getting the power on it shows please insert the localhost loging username and password.
Any one can help me to get the Localhost loging credentials.
