We recently announced the release of our self-serve virtual assistant. You can read the full announcement here. Videos and documents are available within a click for our latest products. Once you've told the bot what device you're using, the context ...
Forum Posts
(Updated September 2023 - Added Catalyst 1200 and Catalyst 1300 ) Hello! This sticky-post will serve as a sign-post for incoming community members. Below you will find links to pages that you may find helpful. Catalyst 1200 & 1300 Hardware Install...
Hi Can you advise if the SG550XG-8F8T-K9-NA can be stacked with theSG500X-48-k9-NA? The documentation available speaks to stacking of the SG500XG-8F8T-NA stacking with SG500X-48-K9, however since SG500XG-8F8T-NA is now end of sale and has been repla...
Morning all, Having some issues with my Sophos XG firewall adopting APs. I have narrowed it down to the config on my smart switch (SG500-28P) as it will work with a dumb switch that I connect to it and my firewall can see the AP. The network is f...
Resolved! Stacking SG550XG and SG550X
Hello, I couldnt find this question on documents. Is it possible to do a hybrid stack between SG550XG and SG550X series ? SG550X-24 - SG550XG-24F Thank you
Hello everyone, I post a thread and a user told me that I would probably get some better result in here. So the story is that we have a switch (SG200-50) that has 4 different vlans (1 untagged and 3 tagged). The thing is that a couple of times per ...
I have a Switch sf300-24. Can anyone send a configuration examples on how to configure vlans for voice and data via the command line? I keep having trouble. I have router setup for dhcp for the data. I set my data on 192.168.1.X and voice on 192.168....
I have not so advanced but also not used sg350-28p cisco switch. Our college has obtained it as a donation from a sponsor. It was unpacked and looks like completely not used and new device. The switch was switched on with serial blue cable and putty ...
Hi, I have been using SF300-24P 24-Port 10/100 PoE Managed Switch since 2 years and i never faced any problem, but from last couple of days it is showing orange color blinking light on system. I have restarted the switch but it didn't fix the probl...
Hello everyone, My client has asked me to run rapid spanning tree on his cisco switches. The first one is a WS-CS2960G-24TC-L running 12.2(25)SED and C2960-LANBASEK9-M. The second one is also a WS-C2960G-24TC-L running 12.2(35)SE5 and C2960-LANB...
Resolved! SG350XG-2F10 supported SFP+ transceivers
Hi everyone, this might be my second post over cisco support forums. recently we have been finding 10g enabled switches for our network. finally our search landed on cisco 350XG-2F10 switch. actually we needed both rj45 copper based 10g ports and S...
We have a couple of SG-300 in a lighting network on seven stages. Every SG-300 is setuped with two VLAN. VLAN1 is for fileserver and remotes. VLAN2 is for sACN, a networkprotocol for distrubute lighting data (as ArtNet). Most of the stages lighting...
The network management software(solarwinds) receives the switch svi port packet message,It report "Interface 'unrouted VLAN 19 - VLAN -' the packet loss rate was 10.647%, the threshold of the monitor is 10%" But the vlan does not contain any device...
I have two SG300 switches connected via a port channel that contains two 1Gig links. I have two video streams that I need to send across the link that are each just under 1Gbps, hence I need to ensure that the port channel is load balanced properly....
Hello! can you confirm that SG350XG-2F10 support stacking on on-board 10G BaseT ports, using Cat6A patch cord ?
Hello, I "inherited" a small network from a former colleague. It consists of four Cisco 2960 switches (WS-C2960-24TC-L). The switches are connected to each other via GLC-SX-MM= SFP transceivers. I would like to replace one of these 2960 by a new SG...
I have a small business that is going thru a little growth and I am upgrading my equipment which is turning out harder than I thought for VLAN setup. What I want to do is very simple, but I am not able to figure it out. My setup\needs are as fo...
