Switches - Small Business

Hi There!  This is my first post and I have no idea what I am doing when it comes to SNMP.  We are trying to evaluate our network performance, so we have downloaded a copy of Solarwind’s Orion and installed it on a server.  The topology is as follows...

I have a workstation on this switch that is running WireShark and I need to get packets to it.  However the moment I turn on port mirroring the station loses IP connectivity to the network.  I tried Rx only, Tx only and both and all three settings kn...

Hi,My Linksys SE2005 (v2.1) switch does not work with my Belkin N1 Vision router.If I cable a PC direct to the router it works. If I cable via the switch it does not work - the PC cannot configure the network settings (it can't even access the router...

I have a Linksys SGE2010P 48 Port switch with POE and I cannot get the firmware to upgrade.I have downloaded the firmware software from the site: http://www.cisco.com/en/US/products/ps9985/index.htmlEverytime I run the EasyUpgrade application I get t...

Hi there again,after upgrading our sge2000 from fw 1.0.0.45 via 3.0.0.17 to finally 3.0.0.18 we cannot upload the previously backup'd configuration files. first comes the msg "copy failed", then "copyjob completed with errors". but the configuration ...

Hello there,we have a server deploying images via pxe to several clients the same time and want to enable muticasting at our sge2000 switch. i tried to read the help/support manuals of the switch concerning multicasting but i have no clue (and don't ...

I have what is hopefully a simple question.  I'd like to know if any of the small business switches (e.g., the SRW2024) will work with AT&T uverse.I have my house wired for gigabit, and am getting uverse installed this week.  I have one gigabit (rj45...

Hi,I try to configure an etherchannel trunk but I´ve no success.So I need a step by step guide to configure the trunk.I´ve 6 vlans defined on the Switch:VLAN1VLAN121VLAN122VLAN123VLAN999Now I need an etherchannel as trunk (ports g7 and g19) with the ...

Just purchased 1/2 a dozen SG100-24 switches which I was planning to use in our switch rack and uplink into our HP Procurve switching backbone ... but when I connected port 24 up ... nada ... nothing ... doesn't light up ... no traffic.In the past we...

Hi,We're facing a strange issue with one of our SRW2024 Switches.We already have many of them in production with the following configuration :interface vlan 2ip address 10.10.10.1 255.255.0.0 Some ports being on the same VLAN, some in access mode, so...

I'm managed switch no0b and I'm unfortunately running into a wall configuring it. Some background: My IP phones and VOIP service is all provided by an offsite company, however for cost purposes they no longer provide networking support for my office ...

I have a standalone 1142 AP.  It is connected to a Cisco ESW switch.  For the guest wireless network, I put VLAN 12 on the AP with open authentication.  I added vlan 12 to the switch.  I added vlan 12 to the port the AP is plugged into and the port t...

All,I have a customer with a single Cisco SRW2048 switch that has been installed at the network core and is due to replace two aging HP ProCurve 2524 Switches. Previously, the HP Procurves were linked via Fiber to similar HP ProCurve 2524's in a netw...

We are looking to use some SRW2048 in replace of some 2960 switches.  Do the SRW2048 support extended vlan ( 1-4094 )Thanks,Jason

Hi,I recently bought a SRW2024 for use in a small office environment.In the web GUI setup summary page it reports ports g9 & g10 as up, when in fact they are down. The CLI shows the same status.The LEDs are not lit for these two ports and there is no...