We recently announced the release of our self-serve virtual assistant. You can read the full announcement here. Videos and documents are available within a click for our latest products. Once you've told the bot what device you're using, the context ...
Forum Posts
(Updated September 2023 - Added Catalyst 1200 and Catalyst 1300 ) Hello! This sticky-post will serve as a sign-post for incoming community members. Below you will find links to pages that you may find helpful. Catalyst 1200 & 1300 Hardware Install...
Hi,I have a SG200-50P. It had a problem with the PoE ports (didn't supply power to my Bosch POE security cameras) so I updated it to the latest firmware. Now it does recognize the cemeras and supplies power to them. However, there are a few proble...
I have SG200-08P. It was purchased in 2017 so I have no warranty.The power supply is dead so I need to find a new one. Where can I do it?How (where) can I check the device itself?
Resolved! SG550X Capabilities
Hello Everyone, We have a number of Cisco SG550X-24-K9 switches, they are used as ToR switches for the Data Center (physical servers). I enabled jumbo frame on all switches, but I am unable to set the MTU of the interfaces, neither from the UI nor fr...
Hi,Recently, I've changed my switch from L2 to L3 mode, I did a reset as well, I've some problems with the switch, currently this switch is using with MAC Add lock down for all the ports. 1. I am unable to see which MAC Add that causes the port to ...
Hello, I'm simply trying to create an LACP link between a SG500 and SG500X. The problem is on the SG500X which is the new switch I'm setting up - there are already other switches using the SG500 with an LACP link just fine, just this SG500X is givi...
When a new unconfigured SG350X switch is add to a infrastructure, i know that its possible the stp / rstp may choose a new root bridge. but is it really correct that then some LAGs blocking between the other switches for a short time? Especially when...
Hello, I noticed that after restarting the SG 200-08P, all information that was stored in LLDP MED device location is deleted.Only the ID survives a restart.I don't think that's right. Best wishesDetlef Paschke
Hello, i want to rout 3 Switches to 1 with the Vlan 400 with the IP 10.4.0.254/24so i Static Routed on the 172.16.204.251 Switch Destination:10.4.0.0/24 Next Hop:172.16.254.40and on the 172.16.254.40 Switch Destination: 10.4.0.0/24 Next Hop 172.16.20...
I am getting this when I look at my RAM Memory Log on SG300. The link keeps going up and down. Is Portfast causing this or a flaky NIC?
Hello Professionals, Device: SG300-28MP 28-port Gigabit Max-PoE Managed SwitchFirmware: 1.4.11.5 I have added VLAN 10 and 20 with 192.168.[VLAN].254 /24 with access ports for VLAN 10: GE1, GE2 and VLAN 20: GE20 Also I have added two trunk ports GE25 ...
Hello, I have several SG200-08(P) in operation and for several years there has been the problem that configuration with current browsers is not possible without errors.The SG200-08(P) can only be configured reliably with IE or with Edge in IE mode. h...
My name is Alvaro. Its the first time Im using the Cisco Support Community.Im looking for the MTBF numbers of 2 Cisco trasceivers:- SFP-10G-SR-S- SFP-10G-T-X Sometimes they are provided in the datasheet, but for these products I couldnt find them.So ...
Hi,I have the following rather basic question, but google doesn't seem to help me any further here. The situation is the following:router <-> L3 switch (Cisco CBS 350) <-> servers/clientsrouter is on VLAN 192.168.255.xservers and clients are on diffe...
My case No :- 691659870,Moel No. :-SG350-28 Port Gigabit Managed SwitchSr. No. :- DNI233809F1 Country :- INDIAEstate :- maharashtradistrict :- MumbaiMy name :- Surendra GuptaMobile No. :-+91 8451846155
Hello!The question is -- can I have 40G through-the-stack bandwidth for the 3 or more SX550X-24F units stacked in ringor it's just 20G maximum? Seems I'm a bit lost while reading Administration Guide.It is declared that:"1) When two neighboring units...
