Switches - Small Business

We have configured a native stack with two Cisco SG350XG-24F. We are using the stack configuration for two reasons:1. to have a redundant connection from the hypervisors to the shared storage2. to aggregate two uplinks to an other switch (one port on...

SG200-26 26-Port, firmware 1.3.7.18I have MTU mismatch on the network and the last device that can be responsible for the mismatch is my Cisco SG200-26. I was looking long and hard for where I can at least check what is the value of MTU on the switch...

We have a Switch SG500-52P connected to a 2960x using a Single Mode fiber through the port g1/1/49, and also it is connected to two other SG500 switch through the ports G1/1/19 and G1/1/36 respectively. by copper links. There is no redundant links im...

Hi,  Somebody help me to describe.  I'm used   SG550X-24 Stack unit  to core-switch   and  SG220-26P  to access switch  config LAG  mode auto on both switch.Sometimes  clients are disconnect from system 20 minutes.  Then I check log on both switch  f...

Hello,I bought a Cisco SG200-26 and am currently setting up the VLANs.Is my first Cisco router, therefore something new.Now i have a question:By default, the VLAN mode is set to "Trunk" everywhere (as can be seen in screenshot1).On the Cisco, the Por...

Hello ,I am a new user .I am trying to work on 2 scenarios with SG350 L3 switch. Scenario - 1I am trying to terminate WAN conection on on one of the Fiber port of the switch. ISP box is connected to SG350 via fiber patchMy ISP gives /31 public addres...

Hi, After having set Management ACL rules on my switch, I enabled the DNS resolution to properly poll sntp serversHowever, I noticed theses warnings, received on a regular interval:Warning %MNGINF-W-ACL: Management ACL drop packet received on interfa...

Hallo,i bought a used Cisco SG200-26 Switch, with which I want to use 4 VLANs.VLAN100 Ports 1-6VLAN200 Ports 7-12VLAN300 Portd 13-18VLAN400 Ports 19-24I set that up and created it works so far.I connected the Lan Port2 from the Modem (AVM Fritzbox 55...

Hi Team, What is warranty of Sg500X and SG300.. before purchase. Thanks & Regards,Sachin Chopade 

Hi, My question to the product warranty period: Cisco warranty finder says: 90 day or 1 year. Info page says: "limited warranty" what is correct one? Product: SG 300 - 10 port and SG 300 - 28 port Switch. I did use: https://cway.cisco.com/sncheck...

Please suggest me 1. how to change  default user name and password through CLI mode of Cisco SF 300-24 switch 2. How to configure port security through CLI mode in  Cisco SF 300-24 switch

We have procured 5 Cisco 350GX 24 port Switches. Each site is connected with one Cisco Switch to Fritzbox 7590. Current setup:- Fritzbox has an Static IP configured from ISP. DHCP is enabled on the router itself. It has 4 LAN ports and 1 WAN port.VoI...

Hi I wondering if anyone might be able to help me with a port trunking issue I can't seem to wrap my head around!I am very new to networking and Cisco switches in particular - I have had a dabble with HP switches in the past mainly the ProCurve range...

Hi,On the SG350, I thought I could apply some VACL or ip access-group, but these commands are not supported it seems !The only way to bind an ACL to an interface isservice-acl input# the output version is not supported it seems ! service-acl outputI ...