Hi, I am confusing performance of SVI and Inter VLAN routing. I would like to know which is more best practice. I have two scenario. Eg. 1. cisco c892 have 2 x 1G WAN port and 8x 1G Switches port.we can configure one port as a trunk port and i create...
Forum Posts
In my environment we recently installed some Dell 4148-on core switches, they will be running OSPF however the routers and ASA's are running BGP and EGRP. What do I have to look out for and is there any configuration on the routers and ASA's I may n...
I am trying to replace a failing Cisco C3750 switch with a Meraki MS250. I have about 14 VLANs. The problem I have discovered is that the Meraki switch does not support RIP so interVLAN routing is failing. I have two stacks of C3750s as well as three...
Can some one help me my router got stuck in rommon mode. below the out put. after resetting I copied running config to start. thanks. rommon 1 > confreg Configuration Summary (Virtual Configuration Register: 0xc400)enabled are:diagnostic modeuse n...
Having issues on a system I am using for class its a 2 client 2 router a switch and a web server system. right now im trying to configure PAT on router 1 and then from client 1 ping a serial port on router 2 through router 1. the ping is successful ...
Resolved! DMVPN and Point-to-Point (IPSec)
Dear All, PLease help me: I would like to know DMVPN and Point to Point (IPSec) can run in one router ? I mean two type of VPN can run together ?If i will use GBP for DMVPN ,how many RAM will need in minimum ?For BGP in DMVPN, my remote as is ISP AS ...
Looking for some advice on configuration for a new 5506-X. We have multiple interfaces that have some limited services allowed between them. For the INSIDE network, I would like to allow internet access. The only thing I can seem to do is add a INSID...
Good day everyone - i'm working on deploying QoS across our corporation and have a few questions - i'll keep it simple as for layout of network. WAN(MPLS) -----(CERouter)----(OurRouter (2901)----(Switch(2960x)----devices (ip phone, desktop,etc..) ...
Hi, quick query to confirm I'm adding OSPF statements correctly. On our core L3 switch we have an existing ospf config (ive left out all details apart from one example) i.e. router ospf 1 router-id x.x.x.x network 10.10.10.0 0.0.0.255 area 0...
Hello, I have a upgraded one our public facing routers from 2951 to ASR1001-X. Since then I have connectivity issues with one of our BGP neighbors. The problem is, no return traffic is received from the neighbour. - BGP peering works - Receiving ex...
Hi, Our customer is looking into using 5921 running on an system with high end I7 processor with 16GB RAM and trying to use it as replacement for EOL 5940 router. 5921 has a bandwidth limitation of 200mbps ( Cisco 5921 ESR Adv Ent SW - 200 Mbps) as ...
Resolved! Configuring Mgmt0 On NX7K
Hello, I configured the mgmt0 interface with an IP address(10.1.200.6/24) that's on the default vrf (vrf default) and connect the port to an ethernet port (Eth2/10) on the same chassis. I configured the default route as follows:interface mgmt0 vr...
Afternoon All, I was wondering if someone can give me a hand with troubleshooting an issue I have on my Cisco SG300-10 switch. Setup Cisco SG300-10 switch in L3 mode WatchGuard Firewall with x1 interface on 10.0.1.1 DHCP is turned off on WatchGua...
Hi All , I am testing the below topology and need inputs from experts on how to stop asymmetrical routing . As per the above diagram , Traffic from LAN to WAN &&& WAN to LAN of Data centers is as below ----------------------------------------...
Hi , I have ISR 4221, with 2 gigabit Ethernet ports and 1 LTE port. I want to use the LTE port as a back up line, when the cable connect is down. but i cant get it working. Below is a snip of my configuration, what did i miss chat-script lte "" "...
