Switching

Discuss Catalyst brand switches with peers and experts.
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

Get 20% off switches when you combine Cisco solutions

 
Labels

Forum Posts

When I try to copy image from switch to tftp its showing error but connectivity between  tftp and switch is working fine please find the below logs.   sh flashTech-C2-FCore01#sh flash Directory of flash:/   517  -rwx        5144   Mar 1 1993 05:31:07...

yogesh1 by Level 1
  • 85298 Views
  • 25 replies
  • 0 Helpful votes

cisco 65 VSSCan I  config auto-recovery feature like VPC if active switch goes into recovery mode? I haven't found this feature on 65 VSS.thank youTom

fly by Level 2
  • 850 Views
  • 1 replies
  • 0 Helpful votes

Resolved! two exit routes

Hello,   An access switch is connected to two routers.  The switch has a single default route to one of the routers.    Is it possible to add another default route on this switch(keeping the original one as it is) without any issues? Will adding a se...

suthomas1 by Level 6
  • 7720 Views
  • 15 replies
  • 0 Helpful votes

Hi,Is there a way to track an interface in Cisco routers and if that interface is down to bring another interface down as well (e.g. if fa0/0 becomes down, bring fa0/1 down)?I found this link in Cisco website but it is not exactly what I am looking f...

I have one Cisco SG200-50 switch on my network and a AP 1602i. I have now also connected a Sonos One SL to the network.At first I had no problem setting up the Sonos and connect to it. Now after one day I am unable to connect to the Sonos with the ap...

trih by Level 1
  • 1891 Views
  • 13 replies
  • 0 Helpful votes

Hello,I have a 6509 switch that once rebooted goes to the rommon prompt and requires me to intervene in order to get the switch to boot.As far as I can see the boot command is OK and the boot variable points towards a file that exists in the bootflas...

Hello everyone, I am currently able to authenticate my phones via MAB in ISE, we currently add the mac manually, I understand that a profile can be created to make this dynamic but I have not found documentation on how to do it, open a way for ISE to...

eperezb by Level 1
  • 402 Views
  • 0 replies
  • 0 Helpful votes

Hello, I have two switches 3850 with 10G expansion module and a 3750 with 1GIG SFP.3850 has a SFP+ 10G fiber connector and the 3750 has the 1G SFP fiber connection. There is no link.Adding a 1G to the 3850 and keeping the 1G to the 3750 will allow a ...

JB-TX by Level 1
  • 938 Views
  • 4 replies
  • 0 Helpful votes

 Purchased a C3850-12X48U (1G, 10G, 40G) Along with a 10G Fiber Upload 8 port module.There are some random interfaces that are not physical on the switches CLI. Can anyone shed some light for me? interface TenGigabitEthernet1/0/44 <--- Physical ! int...

JB-TX by Level 1
  • 949 Views
  • 5 replies
  • 0 Helpful votes

  Can anyone help me to follow best practices to create QOS on Nexus 9K?Thanks! SW1interface Ten-GigabitEthernet1/0/1qos priority 1interface Ten-GigabitEthernet1/0/2qos priority 3interface Ten-GigabitEthernet1/0/3qos priority 5SW2 - Nexus 9Kclass-map...

Hello everyone!Can anyone answer why, after entering the command "show route-map" packet counters show zero matches?We have other Cisco 3850 switches in production, stand-alone switches and in the stack, but all of them shows zero in counters, but pb...

Hi, newbie question here, looking for the steps to move an existing switch in a stack to another existing stack please. I am pretty new to networking so please be gentle. Removing the switch: - What are the steps in terms of physically disconnecting ...

Mottok by Level 1
  • 2020 Views
  • 4 replies
  • 0 Helpful votes
Review Cisco Networking for a $25 gift card