Hi All,I have to put one of the above in a cabinet in another building.I want to protect it with an UPS but to do that I sort of need to know what the power consumption is.I've looked at various Cisco data sheets but none of them seem to know the ans...
Forum Posts
Hi Cisco Peeps, I have a Cisco 2960-S Model:WS-C2960S-48LPS-L, I upgraded to IOS 15.2(2)E9 then after the upgrade,"boot system flash:" is not appearing and I want to roll back to 12.2 IOS (c2960s-universalk9-mz.122-55.SE5). boot system c2960s-univer...
Hi there, I'm trying to figure out which physical ports on nexus 2000 connect to 5000?I did show command on 5000: show interface fex-fabric. but it only showed the ports on nexus 5000. I'm looking for the ports on 2000. Does anyone know the ...
Folks,I was wondering if someone would be able to assist, basically i need to create a couple of vlans within a vtp domain and allow routing between them. I'm a bit of a novice and don't work on Cisco products as often as i'd like to. Requirements...
Resolved! sg300 - remove trunk of interface
hi all,got a real problem, im trying to remove a trunk of an interface as its just automatically made it a trunk and i have no idea whythe interface in question is g1/0/7i made it an access port and it still is an access port but aswell its made it i...
Is it possible to schedule a reload of only one member of a 3850 switch stack? see below ... -=-=-=A1#reload slot ?<1-9> Slot number of RP or line cardA1#reload slot 3 ?<cr> A1#reload at 23:59 11 December testing ?LINE <cr> A1#reload slot 3 at ?% Unr...
Hello everyoneWe have Catalyst switches in our network, up-linked with 1Gb ports. Although these ports are handling less than 10-20% percent traffic at peak time, they are reporting output drops. All monitoring systems also show low traffic utilizati...
Hello, hoping someone can help or point me in the right direction at least! I am replacing a 3750 stack (v12.2) at one of our sites with a stack of new 9200L switches (v16.9) - the majority of the config I've been able to transfer across with a coupl...
Resolved! Port Channel to Server configuration
Hi all,I've connected one of my servers two ethernet connections to two ports on my 350XG switch. The ports are configured in a Port channel (PO1) which is configured as a trunk port. Am I right in thinking that the port channel is set in active / pa...
I have a Catalyst 2960-X stack that I am trying to configure.I am able to log into the web interface. So I can log into the web interface and deal with the very limited interface there (I can enable/disable ports if I want there), but if I want to lo...
Kindly explain below command meaning--switchport port-security maximum 2switchport port-security violation restrictswitchport port-security aging time 2switchport port-security aging type inactivityswitchport port-security
Hello All. There seems to be some strange things going on, when we connect a new device such as a laptop or server to our 3750 we cant ping it for a while from another device, but as soon as we try to ping it direct from the 3750 it starts to work. I...
I have a Cisco 892 running version 15.7(3)M4a. I configured DHCP snooping on it. I have a trunk on the Cisco 892 configured as an uplink to a Cisco layer 3 switch that is acting as a DHCP server, and I have a Windows box connected to an access port t...
Why are there so many different CEF commands, and what is the difference between these commands? A few examples: "sh int <interface> switching" vs "sh ip cef switching statistics feature" -> both of these show how many packets have been process switc...
All, I have a nexus 3k acting as LAYER2 only and it is directly connected to an ASA routed mode with Subinterfaces. All my ports that are configured and trunk ports send traffic properly, but my interface that is configured as an access port is not....
