I need help with TFTP command syntax. What is wrong here? image resides on solarwinds TFTP within C:\TFTP-Root. Devices are reachable too and TFTP service is active. SWITCH#copy tftp: flash:Address or name of remote host [x.x.x.x]?Source filename [...
Hello, I'm going to be upgrading some Cisco N9K's to current gold-star code. They're currently setup in VPC configuration. I've upgraded Nexus switches before, but i'm just wondering if the switches being in VPC configuration would have any impact. C...
hi, I am trying to configure the Netflow lite on the 2960x. Core L3 --- 2960x L2 switch --- Core L3 None of the core is supporting Netflow. L2 swith is configur with VLAN 30 to enable routing. I want to catpure the netflow. Configuration applied: fl...
Hello!My company develope many electronics devices, and we want make module like PCL - it will have RS-485, digital in/out but we want make it as IE-3300 expansion module like IEM-3300-8T.Can we take power and idealy one ethernet from IE3300 bus?I at...
Hello all cisco website says,"""""This list shows how PVST+ interoperates with IEEE 802.1Q or IEEE 802.1D, if the Native VLAN on an IEEE 802.1Q trunk is VLAN 1:VLAN 1 STP BPDUs are sent to the IEEE STP MAC address (0180.c200.0000), untagged.VLAN 1 ST...
need to block network traffic from vlan wifi guest to other vlans resources like (lan/wifi office/printer/mgmt/server/cctv and so on)so wifi guest vlan can access intetnet only vlan wifi guest cannot access other vlans but vise versa is ok ... ( am ...
Hello all,We have third party firewall cluster. We are configuring Azure Express route in our infrastructure. On Microsoft side, there are 2 vlans for Microsoft peering and one for private peering. They also have primary and secondary connection for...
nhm-svr-nx-01# sh run !Command: show running-config!Time: Tue Sep 10 13:52:43 2019 version 7.0(7)N1(1)hostname nhm-svr-nx-01 no feature telnetfeature tacacs+cfs eth distributefeature ospffeature pimfeature eigrpfeature interface-vlanfeature hsrpfeatu...
Hi,We are getting following logs on regular interval for ip sla003902: Aug 27 13:54:03.494 IST: %TRACKING-5-STATE: 10 rtr 10 reachability Down->Up003903: Aug 27 14:05:08.585 IST: %TRACKING-5-STATE: 10 rtr 10 reachability Up->Down003904: Aug 27 14:05:...
I'm currently experiencing an issue where my 3850 is no longer booting with the IOS is goes directly to the switch: prompt.When I do a DIR command it doesn't show the Flash: directory. I tried to perform the Flash_Init with the Emergency-Install usin...
I have deployed a pair of Cisco Nexus 93180 in vPC. I am routing using OSPF and BGP. I have noticed that when I do a show ip route the only default route I see is via the mgmt0 interface, but this interface sits as part of the vrf management so not s...
Hello for everybody. What is purpose of "show switch" command for catalyst 9500? Switch#sh switchSwitch/Stack Mac Address : 00b6.7038.c400 - Local Mac AddressMac persistency wait time: IndefiniteH/W CurrentSwitch# Role Mac Address Priority Version St...
Hi all,I have a second hand AS2509-RJ that I'm unable to get access to as I don't know the username & password. Is there a way to factory reset the access server?Thanks in advance
What is the maximun number of "ip helper-address" that i can put in a Vlan?
So i have a question regarding to switches i have looked over the prices for switches and i can make no sense at all. for example , in my internal LAN , i want to replace 5 or so switches. the problem is however that i came across on 2 devices which ...
