Resolved! printf with blocking disabled
Hey! my Cisco router occasionally prints a strange log like: %SYS-2-NOBLOCK: printf with blocking disabled Is this normal? Is my router faulty? Thanks!
Hey! my Cisco router occasionally prints a strange log like: %SYS-2-NOBLOCK: printf with blocking disabled Is this normal? Is my router faulty? Thanks!
Hi all, Here is the situation I find myself in. Our company has a data center which currently has around 5000 machines operational in it. To keep it simple it's a cryptocurrency mine with dedicated mining hardware, i.e. not general-purpose comp...
I have just installed a Xerox 8560 MFP printer and as I am running 6 different vlans I don't seem to be able to get the scan to PC function working.If a pc is on the same vlan as the scanner, it works no problem. If I try to scan to a pc on another v...
Hello We are quite new to Network /Switching concepts and we have a question on one of our CISCO industrial Ethernet Switches IE-4000-8GS4G-E to evaluate the switching capabilities. As we see , there are 12 Ethernet based ports. However we see 4 add...
HI, everyone! I can't instal IOS (cat3k_caa-universalk9.16.03.06.SPA) on WS-3850-12S. An error occur. Before the installation I cleaned up memory. I tried to install cat3k_caa-universalk9.16.08.01a.SPA and cat3k_caa-universalk9.SPA.03.07.05.E.152-3.E...
Hi, I searched bug tool and other resources for this behaviour. Am I missing somthing obvious, or is this a bug? Configuration is not saved to port channel interface. It´s also removed when shutting down a port channel, like "conf t - int po1 - shu...
Hello, My Cisco switch keeps sending the following syslog: %PARSER-3-URLOPENFAIL: cannot open file for redirection 'Timed out' Does anybody know what it means and what should I do?
Dear fellow engineers, We are a small ISP and we have customers who subscribe our IP transit services. Currently I'm using class-map and policy-map to limit their bandwidth as you can see in this config. Then I apply policy map into sub interface i...
Dear all, I tried to enable flow-control on my interface but from a "show interface" it show me that is not supported. Here my configuration : interface GigabitEthernet1/0/48 switchport access vlan 51 switchport mode access flowcontrol receive on...
Hiin my scenario i enable debug interface fastEthernet 0/0.But this command has no output.What output should this command expect?
Hello everybody! I have this scenario: My main router is a 1921 ISR Multiple local networks assigned to multiple VLAN's, and connected to three Internet Providers. This providers are just standard services (three different cable providers), so I have...
This works on SG300, but not on SG350: conf t int gi1 switchport mode trunk switchport trunk native vlan 111 switchport trunk allowed vlan add 20 switchport trunk allowed vlan add 30 Last two lines are merged into single one when sh run int gi1 swi...
Is there a way to set a traditional loopback address in FMC? I would like to use a loopback address for solwarwinds management and troubleshooting but have been unable to find a way to configure one via the fmc.
So I have a pair of 93000 Nexus switches. One switch is pointed to and using the following fine: kickstart variable = bootflash:/n3500-uk9-kickstart.6.0.2.A8.9.bin ...
Hi guys. I'm studding for CCNA and im at the routing protocols now. When define which routing protocol i want to use (RIP EIGRP etc), i need to define a network. The router then publish the whole subnet. lets say i have an INT with IP 192.168.1.1/30 ...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
05-27-2025 03:30 AM | ||
05-27-2025 12:59 AM | ||
05-23-2025 10:30 AM | ||
05-22-2025 08:23 PM | ||
05-15-2025 09:37 PM |
User | Count |
---|---|
9 | |
8 | |
5 | |
4 | |
3 |