Hello,
how can I create multiples vlan with one command?
I have to create a group of VLANs 1600-2700, and i dont want to tap every vlan command, is it a easiest way to do it? Its a 2960x switch version 15.2(3E)
Thanks!!
"spanning-tree mode pvst" is not available on my Cat6506E 15.2(1)SY3.
"spanning-tree mode mst" or "rapid-pvst", these are allowed.
How to set "spanning-tree mode pvst"?
I have a point to point connection with an off-site location that we recently upgraded our bandwidth from 100 to 500 Mbps. I had a 2901s on both sides and discovered that 167 Mbps was the max throughput we could achieve.
I recently migrated the routi...
I am doing some DOA testing before I send the switch to site when I noticed that when I issue the show power command I receive the following output.
Power Fan InlineSupply Model No Type Status Sensor Status------ ---------------- --------- ----------...
Hello, I have the following situation:
1. Network1: 192.168.1.0/24 gateway 192.168.1.2
2. Netwotk2: 192.168.2.0/24 gateway 192.168.2.2
3. Network3: 192.168.3.0/24 gateway 192.168.3.2
4. Linux box with the inside NIC with 3 interfaces: 192.168.1.2/24,...
Hey Cisco community!
I ran in to a problem when trying to downgrade the software on our new Cisco 3650-48FQM access-switch. The switch is delivered with Denali 16.03.X and we don't want to use that software at this stage.
I tried to install the fol...
Hi,
The ifspeed OID 1.3.6.1.2.1.2.2.1.5 in RFC1213 is read-only. Is there any other OID/MIB that allows to configure the Bandwitch through SNMP?
Best regards,
Jeroen
Dear All,
i have one C4500 as a core switch connected to access switch 3750X (6 switches as stack) so we have received this log on C4500:
001201: Apr 23 20:35:36.121: %C4K_L2MAN-6-INVALIDSOURCEADDRESSPACKET: (Suppressed 2395 times)Packet received w...
Cisco 7706 HSRP %ARP-3-DUP_VADDR_SRC_IP.
Hi,I have an interesting issue: (btw: I did find some simular bugs in the bugtoolkit, but none seem to fit with what I see).
system: version 7.2(2)D1(2)
The problem seem to be non impacting, as the customer...
Hello experts,I need you help to understand the MAC table output of a cisco WS-C6509-E switch. I was trying to trace the L2 path from this switch to the IP 10.64.130.20 which is the next L3 hopI pinged the IP from my 6509 switch & checked the ARP. Fr...
Aloha!
I would like to set the "admin" password but the User management screen doesn't allow one to change it, it is grayed out. I also tried to run Express Setup and although the documentation shows a password setting fields, they do NOT appear on...
I have Brocade ICX 7450 layer 3 Switch connected to cisco Router 811, from local PC in the switch I can’t access the internet, from the PC I can successfully ping the public IP address at the Router ? Any help will be highly appreciated; the main pr...
Hi All, I've got an issue I am looking to better understand. I've got a pair of 4500-X in VSS as a network core and a pair of N5K-5672 for top of rack. The 5K's are VPCd together and there is a pair links in vPC/Port-channel from each 5K to the 4500-...
Hi,
We are in the process of installing a bunch of Cisco AP2802I-B-K9 Access Points. When we did the first one as a test, the antennas would not activate because they weren't getting enough power from the switch. The switches are 3750X switches. W...
Hi all,
I have a question that may seem dumb to the engineers in this forum. However, but if possible do answer....
In below topology i have to make PC0 should not communicate with PC1 and PC2 should not communicate with PC3.
But PC2 should talk t...
