What are LPD-L, FPD-L, TD-l, FPS-L, PSL and more like wise... for better understanding?
What are LPD-L, FPD-L, TD-l, FPS-L, PSL and more like wise... for better understanding?
Hi, I have a problem with two switch 3750X with IP SLA. Every day I see on the log the message that the IP SLA reachability is down "Jun 2 15:36:52.885: %TRACKING-5-STATE: 1 ip sla 1 reachability Up->Down" but when i set the "show ip sla statistics...
Cellular port is issue .Even particular commands are not working. Please find logs of the same and assist further.. =~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2017.06.05 13:41:13 =~=~=~=~=~=~=~=~=~=~=~= User Access Verification Username: tmbitdPassword: TMB_...
Team, I like to log the traffic which is transiting the switch. Pls give the steps for Cisco IOS /XE/nexus switches Thanks
hi community,we have a "double side" vPC connecting 2 pairs of Nexus 5548 switches across two racks in the same data center. the plan is to move the one rack to another data center 20 km away, but to keep the existing setup the same.present setup: ...
Hi, I have a question regarding my layer 3 switch. Currently, the network works fine except that the layer 3 switch (which is Curly) cannot ping outside the management VLAN, and other devices cannot ping it. Moe can ping all devices fine. So, my que...
Hello. We have to make the manuals how to install IOS or to input configuration to the Catalyst 4506 machine. And, especially we don't know how many patterns there are about it. ①Supervisor Of course,in this pattern the configuration may be not kept....
Hello I am creating a banner. when i put this command then some options are appear . s1(config)# banner ? there are some option appear Line Exec incoming MOTD prompt-timeout slipp-ppp Plz tell me if i set banner on these option then where banner w...
The link connecting from ASR 9k to 7600 is going to udld error-disable state after connecting few seconds..The physical fiber is fine and we tested the same fiber from another ASR 9k too 7600.
Hi Guys , We have observed with one of customers that their switches are having High I/O memory utilization. This is constant at 80% and we would like to know if this is normal behavior with the switches. I checked on few other switches of the same...
Hello I have one user Admin and i have to configure telnet session. Admin can create multiple telnet session at a time. But i want to do, Admin can create only one session at a time. Please tell me how i can do it. thanks
Dear Team, We are getting following error on the nexus switch, cisco Nexus 6001 Chassis version 6.0(2)N2(3) Syslog: 2017 May 27 23:47:17 switch01 last message repeated 1 time We are receiving above error repeatedly. Hence kindly do the needful....
I purchased a cisco 4351 isr router from third part vendor. When I ask him about license he told license is loaded . I have only IP base license but I needed advanced IP service what I have do to get it? Is I have to purchase it spreatly ?..... Thank...
Hello, I am quite puzzled with the issue I am having. In my test, I had route-leaking setup. Saved the configurations and turned off the router. Next time I boot up the routers, my route-leaking isn't working. Problem:1) Computer VRF cannot ping any...
Hello, Please tell me, if we configure line vty password then it is not secure. for example. s1(config)# line vty 0 15 s1(config-line)# password 12345 s1(config-line)# login local s1(config-line)# end it is not secure. if we create a user and then en...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
06-13-2025 02:13 AM | ||
06-11-2025 08:26 PM | ||
05-27-2025 03:30 AM | ||
05-27-2025 12:59 AM | ||
05-23-2025 10:30 AM |
User | Count |
---|---|
12 | |
9 | |
6 | |
5 | |
3 |