Hello ,
My Router IOS version is " Cisco IOS Software, C1900 Software (C1900-UNIVERSALK9-M), Version 15.2(4)M2, RELEASE SOFTWARE (fc2) "
I am trying to update server ip address 10.10.10.10 under server name ( NAME_1 ) but getting below error .
s...
I submitted the discussion below in the WAN Switching and Routing Community; but, it may belong here, instead. I didn't see a way to post in more than one community.
I have two Cisco, SOHO firewalls - an RV120W and an RV220W. I am trying to set up ...
Hi,
Please fine my topology attached. I am trying to communicate the between the hosts in 2 different vlans. But my interfaces are down between router and both the switches. Please lemme know the correct configuration.
I have done the configuration ...
Hi Team,
I'm looking for some help, please..
I've deployed a new switch (cisco WS-C3850-48T) with minimal configuration, like an ip address on mgmt interface and vty with trasport input/output as ssh only. I've create a local login say cisco/cisco ...
I have two main datacenters (DC's), which each could obtain an EIGRP route. This learned EIGRP route is from a VPN tunnel RRI (reverse route injection), which either terminates in one DC or the other. So the DC's will not have the same origin sending...
Machine A (192.168.1.1/24)---- (VLAN 5)---- Port (1/1)---Switch A --VLAN 5 ---Port (1/2)--------- Port (1/1)---- VLAN--10--Switch B-------Port (1/2)----VLAN 10)-------Machine B (192.168.1.2/24)
1) Machine A is connected to Port 1/1 ( VLAN 5) of Swi...
Hi,
I am working on packet tracer. I have a topology below topology.
I have connected 2901 router to 2 switches (2960).
Vlan 10 is configured in switch 1 and Vlan 20 is configured in switch 2.
Ip address of host in switch 1 is 192.168.1.10 and ip ad...
Hello,
Quick question around syslog output , we have 2 5k's (5548 ver 5.2(1)N1(4)) running in VSS mode (connected back to back via the management interfaces).
We are not getting any syslog output to our syslog server from either 5548.
Can anyone giv...
Hello,
I want to upgrade my Cisco ISR 891 IOS from 15.3(3).M5 into 15.4(3).M5 or 15.5. but it is not getting upgraded.
I removed the "boot system command from old and replaced it with new IOS 15.4" as shown bellow, but still when I reload my rout...
hello guys,
we have 4900M distribution switches with 10G links connecting to our core switch 6500.we are looking to upgrade our links to 40G. so this means the core switch will be replace by a nexus 7000 switch that can cater 40G.. Question: Can we...
Hello everyone,
I'm trying to deploy a new syslog server on my access switches.
This syslog server is behind load balancer (F5) and vip (virtual ip add) .
The udp port 514 is working on the server and everything shoud be properly configured, indeed o...
everytime i try to restart my switches "3560" with the reload command the telnet window closes or if im connected through the console , the console would stop responding , is this some sort of security thing? is there other commands to restart the sw...
Hello
I'm currently implementing vlans for our company's network, but things are getting little complicated.
I've done with basic configurations, created the vlans 10,20,30 ... and defined a last resort static route to the gateway which it is a sop...
I recently saw a Cisco document that states the Cisco Aironet 1600 EOL is December of 2016.
I am looking for an inexpensive autonomous 802.11n or ac wireless AP. This is for a small office of only 3 people so there is no need for an expensive WLAN...
