Switching

Discuss Catalyst brand switches with peers and experts.
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

Labels

Forum Posts

Hello, Cisco Community!I’m really happy to share that I’ll be hosting the Cisco Community Lab Series, a brand-new hands-on learning journey designed to help you build practical networking skills step by step.Every Thursday at 8 PM EST, I’ll post a ne...

Hi All,I am looking for some guidance on how I can configure my cisco 2611 router with my fios connection and set up a remote VPN?  I want to use it this way so its always on and I can use it to study for my CCNA.  Do I have to bypass my fios router ...

Resolved! Routing Question

HiAs Per the attached diagram we have site1 and site 2 and the AS number is spanning all 4 internet connectionsThe LAN is spanned over both sites using OTV.My question is if we have a server in one of the sites talking out through a pair ASA’s for th...

Resolved! Cisco VTP question

The VTP revision number increase by 1 while adding or deleting a VLAN. My question is , is  there a limit to the configuration revision number. I mean can the revision number can be goes to 10 digit number or even bigger.

Can i configure DHCP server on Nexus N5K-C5596UP with Layer 3 expansion module? Basically I want to migrate the below configurations from 6500s to a nexus 5K with L3 expansion module? Is this possibl? ip dhcp pool vlan99   network y.y.y.y 255.255.255...

HI, I am using cisco catalust 3560-x series swtiches. And I am new to SNMP. I want to assign IP address to interfaces of this switch, using SNMP.  Kindly help me. Any help, any sugession, is most welcome.Thanks in advanceJeni A

ajeni0001 by Level 1
  • 2041 Views
  • 5 replies
  • 0 Helpful votes

Hi Folks,I have an issue observed in testing.  We have implemented a VSS solution on the 6880-X-LE.  We have two MEC L3 PO's upstream and thus two OSPF path's for our default route.  After creating an event in the lab to put the boxes in Active - Act...

Hello Community,My Nexus 5548UP do not recognized the GLC-SX-MM (GE SFP, LC connector SX transceiver) Module  anywhere of  32 unified ports...I need some assistance about that to setting my infrastructure attached on the diagram.ThanksOrlando

Hello Experts, I currently have QoS settings on my switch:class-map match-any VOIP  match dscp cs5  match dscp efclass-map match-all VIDEO_Conference  match dscp af41class-map match-all ROUTING  match  dscp cs6 policy-map myLAN  class VOIP   set dscp...

Hi guys. We have a large network based on Catalyst 2900, 3600, 6500 series switches. they all are was set up as L2 and only 1 core switch  Nexus 7k on the top as L3 for all vlans . The problem is when we deploy DAI on those L2  switches end users hav...

I've seen some mention of multiple fabricpath topologies, but am unable to find much in the way of example configuration.  Is this a supported feature at this time?  I've got Nexus 7004s at one site and 7010s at another both running 6.1(3).  We've go...

My question is, if we have QOS diabled globally on a 6509 will a switchport trust the tags applied by the device connected to the port? I know the default once QOS is enabled is untrust.Thanks,

cfortune2 by Level 1
  • 787 Views
  • 3 replies
  • 0 Helpful votes

Cisco engineers, I'm looking to add a 3750-x into a productions stack with the following members - Switch Ports Model              SW Version            SW Image                 ------ ----- -----              ----------            ----------        ...

 Hi everyone, Here is setup -----172.24.104.x----Server-----FW------SW1--------EIGRP nei   SW2-------EIGRP nei-------SW3------user  PCUser connected to SW3 needs to access server   172.24.104.x SW1 knows route to destination 172.24.104.x via FWSW1#sh...

mahesh18 by Level 6
  • 2604 Views
  • 18 replies
  • 0 Helpful votes