Switching

Discuss Catalyst brand switches with peers and experts.
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

Labels

Forum Posts

Hello, we have a chassis 6509 with this inventory:------------------ show module ------------------Mod Ports Card Type                                              Model              ---    -----    --------------------------------------             ...

rpastrana by Level 1
  • 878 Views
  • 6 replies
  • 0 Helpful votes

Hello Team,I´ve migrated a Cisco WLC connection from a 6509 to a Nexus FEX 2248. The connection is a 2x1 GBE copper Channel. After Migration the WLC still works fine, however I see sometimes LLDP messages on the Nexus as follows:%LLDP-FEX103-3-DETECT...

alf by Level 1
  • 1804 Views
  • 0 replies
  • 0 Helpful votes

Hi!i have two cisco 3750 in stackfirts, master switch have all swports busysecond have only 5how can i see cpu utilizations of the second switch, and its reasonable to move somme devices from first switch to second fordeacreases of cpu and memory uti...

euandrian by Level 1
  • 4037 Views
  • 10 replies
  • 0 Helpful votes

Hi all, This question seems stupid but pls guide me. When we are selecting 4500 switch (for example) as per customer needs, its 10 GE cards dont come with sfp adapters ( as told by my colleague). I want to know is it mentioned in any particular docum...

Jonn cos by Level 4
  • 501 Views
  • 2 replies
  • 0 Helpful votes

Hi,Can anyone help me and verify my configuration?My customer has the following topology. They have thousands of remote sites like this. all have 1 adsl and mpls router, they are running hsrp, mpls is the primary. DHCP servers in the head quaters, 1 ...

evfodor by Level 1
  • 969 Views
  • 4 replies
  • 0 Helpful votes

Hi Community,I recently had some CPU util problems on my 3750-X. The root cause were too many open TCP sessions, which brought the average CPU utilization to 85%. After some research I found a post in the CSC about the IOS 15.0(1). It said, that high...

hiSwitch A connects to Swich B and C using port channel. I am going to bring down one link on each. switch A is server farm , switch B and C are core 01 and 02 . and all are 3750 switches.1. what will be the impact on the network in terms of spanning...

TGF_Cisco by Level 1
  • 343 Views
  • 1 replies
  • 0 Helpful votes

I have the following network. This question is only about redistribution from OSPF into EIGRP on R1.The redistribution is being done as follows (on R1 only):router eigrp 2redistribute ospf 1 route-map OSPFtoEIGRPnetwork 172.30.14.0 0.0.0.255network 1...

Resolved! lacp etherchannel

Hi,We have a single 4500 connecting to two non-cisco devices. We need to enable port channelling or link aggregation between these two.The links are carrying mulitple vlans , hence are trunked and the ip address on either side is used for routing.Fro...

suthomas1 by Level 6
  • 537 Views
  • 2 replies
  • 0 Helpful votes

Resolved! vtp password

hellosuppose i need to add a new switch to an existing network, but no one knows the vtp password. is there a way to know it? or should i reconfigure it in all switches?

ohassairi by Level 5
  • 15081 Views
  • 9 replies
  • 0 Helpful votes

Hi,I have a cisco 6500 and for Vlan 1 This switch is ROOTBut i have Other Vlan Example Vlan 22 , 25For that Vlans this 6500 is not a root switch.My l3 is in VTP server mode also There are 3 L2 Switch Connected with THIs L3 Switch(6500)For vlan22 My s...

Hello,I am trying to have F4 (the WAN interface) bridged to a VLAN interface. I have put my VLAN interface and my F4 in the same bridge-group, set an IP in the BVI Interface, and made sure that VLAN was properly trunked and configured on one of the r...