Team,Could u pls give me the workaround for this error message.Logging to inside 172.16.1.100 errors: 5 dropped: 236What cause the errors.Thx
Team,Could u pls give me the workaround for this error message.Logging to inside 172.16.1.100 errors: 5 dropped: 236What cause the errors.Thx
Hello FriendsI have a question, is there any way to configure (logging or snmp on) the router so it can send all the typed cmd to syslog sever? RegardsSabby
Hi all,I am using cisco c3660 to act as Terminal Server for the communication of production machines in my company, recently there is a communication lost issue happen and its due to physical cable unplug from the machine. to troubleshoot for this is...
Hi.I'm having trouble understanding what the purpose of link local addresses are.Why can't mac addresses be used Initially like arp with IPv4.Why Is an address given In order to find another address ?
Hi everybody1)Does a switch configured with dynamic arp inspection only inspect arp replies received on untrusted port by default or it also check arp request?Dynamic arp inspection according to my book checks target ip address, target mac address ca...
I'm going to be setting up a network with several VLANS and one of the VLANS will be a subnet hosting an FTP server that will be accessible to the Internet by IP only. I have read some stuff online about NAT hairpinning but can't seem to figure out h...
Hi Experts,Just need your assistance in understanding BackBone fast feature...I have a simple topology as below:My understanding is, with backbone fast enabled, when the port Gig0/3 on SW2 receives a inferior BPDU it skips the Max-age then starts its...
I've been curious about this for a very long time, I guess it's time to ask. When the 4500-E series switch boots and if you issue a 'show run' there's several Star Wars themed references and their revisions. Does anyone know what these actually are a...
Hi everybodyMy book says " If you want ip source guard to detect spoofed mac addresses, you wil also need to configure and enable port security"Let say we want ip source guard feature to check both ip and mac address.We use the commandip verify sour...
Hello,As Cisco official documentation says, The Border Gateway Protocol (BGP) Link Bandwidth feature is used to advertise the bandwidth of an autonomous system exit link as an extended community.If we configure the AS in such a way that even the iB...
Hi all,We have remote office where we have 2921 router with 6 layer 2 switches.We have few servers which need to be in specfic vlan.2921 router does not have switching engine we are using this to support VOIP.So on 2921 router i created 6 sub interfa...
Ok we have a switch, all ports are on VLAN1, it was used to extend a VLAN from another location, from the Telus internet switch.So this is how it works, we have a Guest network that people can use, it has its own vlan and we have contractors with the...
Hi allI am trying to understand if this is possible. Any help would be much appreciated.I am planning to use a pair of Catalyst 3750 for QinQ over a L2 link (lan extension)We neeed to have control over what vlans we propagate over this link and we wa...
what's the usual behavior of the switch interface when it's "flowcontrol receive on" is enabled on the interface, Does it buffer the packets for duration of time mentioned in the flowcontrol message or does it drop the packets or is it a combination ...
Hi all,If I have an ASA 5520 with an INSIDE interface, a DMZ interface and a WAN interface what would be the best way to configure NAT? If I configure nat-control and a nat (inside) 1 0.0.0.0 0.0.0.0 this will configure everything to be NAT'd when pa...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
07-23-2025 01:45 PM | ||
07-08-2025 11:44 PM | ||
07-04-2025 02:13 AM | ||
06-26-2025 10:05 AM | ||
06-16-2025 07:47 PM |
User | Count |
---|---|
13 | |
11 | |
9 | |
5 | |
4 |