I have recently loaded a new IOS image to flash: via TFTP. I deleted the old one and then modified the boot parameter. I beleive I missed something because when I reloaded, I boot into helper mode and I have the following prompt.switch: If I show...
I have recently loaded a new IOS image to flash: via TFTP. I deleted the old one and then modified the boot parameter. I beleive I missed something because when I reloaded, I boot into helper mode and I have the following prompt.switch: If I show...
Hello to all,I have a Cisco router 1941 and i need to configure 3g backup. I have got all most every thing to work,WAN link fails 3G comes up, everything seems to be okay, i can ping from router but when i try to ping from PC, it fails. So i think th...
Hi, got a faulty router 2821 with etherswitch module (NME-16ES-1G-P) which I transferred into my 2811 router. The module has no error however the switch module doesn't give any power to our 3 APs (which are getting its power to this module). But it w...
Hello everyone, I'm new here and this is my first post. I'm in need of some help with policy roiting. I have a learning task I need some help with. At this time I need help with the bonus section.ThanksMy Task:OSPF•1. Configure OSPF between routers R...
Hello,How do i calculate available memory on a cisco router. I have did show memory but their is too much information. I also did sh version and i can see that there is 256MB on the router. How do i find out how much is in use and how much is avai...
I have a 2801 running the very latest 12.4(22)T (can't remember what feature set) that is connected directly on a 10/100 Ethernet interface to an ASA5510 (running 7.2(4) - its actually FastEthernet0/0 connected to Ethernet0/2. They are currently con...
I have a Cisco 891 and I although I may never use it, I want to install and at least check out the SDM. When I go to http://router/ all I get is:Cisco SystemsAccessing Cisco 891 "SR891"Show diagnostic log - display the diagnostic log.Monitor the rout...
I have a 2851 router attached to 3750 on a l3 interconnect.The switch sees the router with a "sh cdp neighbor" butwhen you can not see the MAC address on the port the router is connected to.Not sure why?
I seem to be getting this error every two minutes or so. Everything on the switch works ok, including tacacs (I can log onto the switch using my ACS account) so I don't see why I'm getting this error?Can anyone assist?
Quick suggestionI have L3 switch cisco 3750i have configured two vlans assigned ports to it. when i connected PCs to two ports of different VLAN , lets say PC1 in vlan 30 i can ping to different vlan ip gateway i.e 10.10.17.1 but couldnt ping to the...
Hello All,We have a new network with only a 6509 switch and a router/firewall. the switch will have direct connection for users and maybe servers. In this case where there is no other access switch so far, how should the stp configuration look like o...
Hi Guys,
Hi,I do my first steps with Auto Smartports on Cat3560 and Cat2960.Now I'm searching for a solution to have a macro for all devices I don't have a seperate macro.I have five groups of end hosts which I want to configure and I have some printers and t...
Does anyone know if OSPF is supported in the following software release?c3560-ipservices-mz.122-25.SEB4.binI need to upgrade several 3560's in order to unlock the OSPF function. My current versions are listed below if anyone has any suggestions:2 - c...
Hi CommunityI have 3 VLANS configured on a single vSwitch in the ESXi host. That vSwitch is using two NICs (nic1/nic3). How do I configure the Cisco ports and the NIC Teaming under the vswitch to pass tagged and untagged traffic? I have tried to se...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
04-24-2024 11:54 AM | ||
04-24-2024 11:50 AM | ||
04-23-2024 09:53 AM | ||
04-23-2024 02:53 AM | ||
04-19-2024 05:58 AM |
User | Count |
---|---|
11 | |
10 | |
9 | |
7 | |
6 |