route-map outbound-policy permit 10match route-type localset community 3000:999 64810:1000 additive!route-map outbound-policy permit 15match route-type externalset community 64810:1000 additive!route-map outbound-policy permit 20set community 64810:2...
I need some troubshooting help to solve this issue. We have 2 managed routers "A" and "B"across the service privder's VLAN network. The set up is like this->Router A---VLAN "X"--> ISP ATM Switch A<----->ISP ATM Backbone<-----> ISP ATM Switch B<--VLAN...
Hi all,I came across some discussions about GLBP with STP. Like Figure 41 at http://www.cisco.com/en/US/docs/solutions/Enterprise/Campus/HA_campus_DG/hacampusdg.html#wp1108611Cisco's description is wrong there. Even the link between the two distribut...
how tcp/ip layers work.describe function of each layer---Posted by WebUser Razi Hassan
Good morning:I have a problem to create a VLAN with a Cisco 2801.I need to have base ports FastEthernet 0 / 0 and FastEthernet 0 / 1, in the same VLAN.Basically I'm trying to switch access redundacion, now I have redundant switches in which I have th...
Hello,I'm getting lots of problems with dot1q-tunnel on my test lab.In fact i receive traffic on a one client per vlan basis (traffic is PPPoE), i receive all this traffic on a router, collecting all these vlan on a bridge where the pppoe packets are...
hi:i have a question about the direction of Access list. i wanna to control the traffic between vlans. below is the topology. there are three vlans :vlan 10 :10.10.10.0/24vlan 20: 20.20.20.0/24vlan 30 30.30.30.0/24their IP addressed are acquired vi...
Hi all,I received a 4510R+E preconfigured with Enterprise services on it. I plugged into the console of the active sup7-E after initializing the chassis and it doesn't let me put an ip address on any interface. When I use ? command syntax help it d...
I have two 3750G switches stacked together however it's not in a full ring configuration:Stack Ring Speed : 16GStack Ring Configuration: HalfStack Ring Protocol : StackWiseAnd as shown below it's obvious which cable is not working:show swi...
Hi,I’m having an issue with spanning tree protocol. All my network is configured with 3750 switches. I have,. Two core switches. Seven stacks as access switchesAll stacks are connected with two fiber cables to the main core switches. One fiber to pri...
Using one 3560 switch, I would like to create 3 vlans. As followsvlan 5 10.10.10.2 255.255.255.252 vlan 10 10.0.0.1 255.255.255.0vlan 20 10.1.0.1 255.255.255.0vlan 5 connects the switch to a PIX for ...
I bought NAM Module and intalled in my router 3825. The module come with software 3.5 version. I want to install version 5.1.I found some document where I can not update I need to intalla again however I don't find nothing to help. Thanks for your he...
Hi Experts,I have a coreswitch (4507R-E) with dual Supervisor Engine (SupEngine 6-E) + 2 7206VXR Gateways.1st Supervisor Uplink (media-type SFP) connects to 7206VXR (which is connecting to an ISP).SupE6-E-1 <------> 7206VXR-1 <--------> ISP2nd Superv...
Good afternoon,I am currently trying to figure out if it is possible if a router has 4 different networks to assign a different gateway of last resort other than0.0.0.0 0.0.0.0 Dialer 0 for one network.e.g. Network 172.16.16.0/24 is configured on the...
tell me about working of different layers of internet protocol suite---Posted by WebUser Razi Hassan
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 07-23-2025 01:45 PM | ||
| 07-08-2025 11:44 PM | ||
| 07-04-2025 02:13 AM | ||
| 06-26-2025 10:05 AM | ||
| 06-16-2025 07:47 PM |
| User | Count |
|---|---|
| 13 | |
| 11 | |
| 9 | |
| 5 | |
| 4 |
