Buy or Renew
Buy or Renew
NOTICE: You can now engage in the community. Learn about the great new Cisco Umbrella content.

Switching

Discuss Catalyst brand switches with peers and experts.
cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
Start a conversation

Get 20% off switches when you combine Cisco solutions

 
Labels

Forum Posts

Start a conversation

Resolved! Cisco 1711: Cannot get NAT to work

I have a Cisco 1711 which I am tyring to configure as a small-office router. It will assign DHCP addresses to computers on the LAN and provide them internet access. Router receives an IP from the ISP modem and router can ping hosts on the internet. P...

Private Vlan:Promiscuous port trunk

Hi,I have ASA firewall. The Interface is trunk containing 2 vlans (vlan100 vlan 200). That interface is connected to 3750 switch. On the 3750 switch, the vlan 100 and 200 are configured as private vlans which has some isolated and community ports. Ho...

PBR using Next_hop

Hello;I am looking to define a PBR to a number of different gateways based on first the verify availability and then based on source IP address match.I currently have PBR setup to change the default gateway based on the source IP Address defined in a...

811G wan/lan configuration

I have a new 811G with a Sierra Wireless CMDA card (Verizon). After setting it up I can telnet into the router and ping both WAN sites and LAN connections but I cannot ping anything on the WAN side from the LAN side. I assume it's a simple configurat...

020111cla by • Level 1
  • 761 Views
  • 0 replies
  • 0 Helpful votes

Spanning Tree Mismatch Detection

Hi Guys,I have a campus network (mix of 6513s and 2960/3750s) running with MST. In this setup, is there any CLI avbl to identfiy spanning tree config mismatch ?Any hint/suggestion would be of great help.Thanks,Sabut

Resolved! IPService for cat 4506

Hi All    I have catalyst 4506 switch with WS-X4013 (Catalyst 4500 Supervisor IIPlus (IOS), 2GE,Console(RJ-45)) sup engine.i want to configure OSPF on the switch.I searched cisco for IP service image,but didn't find the image.Is this sup engine will ...

anvar by • Level 1
  • 1518 Views
  • 2 replies
  • 0 Helpful votes

SPA-5X1GE= Platform Option

Hi everyone, For Part #  SPA-5X1GE= Under the Platform option, the configuration is asking to select one of the below. Can you please advise and let me know which item I should select and reason for selecting the item please? ( 1 )6500-SPAUSD 0.00SPA...

rahman001 by • Level 1
  • 565 Views
  • 1 replies
  • 0 Helpful votes

Netflow for Layer-2 switched flows

Hello,I observe a strange behaviour with Netflow on Catalyst 6500 with SUP720-3B running version 12.2(33)SXH2a :Setup :Two different Cat6K linked by a trunkA VRF is configured on each Cat6K and connected to a common VLAN (VLAN 310)VRF-A in Switch-A i...

Resolved! Will "no int vlanXX" effect the L2 topology?

I have what is probably a very simple question, I just want to make sure this is going to work they way I think it is.  I have a 6509 with dual MSFC2s doing intervlan routing. I want to remove one of my routing interfaces from the MSFC and let our fi...

STP Limitations

STP is said to have a limit of 7 switches daisy chained together. Attached is a diagram of a network that has a fiber loop, does this meet the condition? Could you add one or two more switches in the fiber loop and still be inside the limitation?

View All
Review Cisco Networking for a $25 gift card