Switching

Discuss Catalyst brand switches with peers and experts.
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

Labels

Forum Posts

PLEASE can someone help figure out what is wrong sometimes the routing table is fully populated with ospf routesand again there times i would have only some network advertised,what could be the main problemonce it happens like that i wont be able to ...

SWLAB100(config)#int port-channel ?  <1-256>  Port-channel interface numberOn my nexus i am configuring vpc using portchanel 2000.On the 6509 I can only go to a max of 256. Is there any new version of IOS that supports up to 4096 channel ids. I know ...

Resolved! PBR Issues

Ok, here goes.I've implemented policy based routing on my 4507 in the following mannerroute-map routeASA permit 10 match ip address acl-routeASA set ip next-hop 10.xx.xx.65int vlan50ip policy route-map routeASAsw-core#sh access-lists acl-routeASAExte...

Resolved! Cisco 3560 + GVRP

Hello Everyone,I have a cisco 3560 with IOS version 12.2(25r)SE1.We buy a switch 3com for access layer, but, i need a help for configuring a GVRP feature to integrated the database vlans in the trunk port.I see a problem, switches 3560 don't support ...

Hi,      I would like to implement IP-Telephony using Cisco UC-520 router. In our Existing Infrastructure we have ISA server 2006 as Gateway and Router also as firewall between the Internet and the LAN     Now I would like to place UC-500 between Int...

Hello,I have a server with 2 nics plugged into my 3750.  both nics can be teamed and I have the option on the server for Smart Load Balancing and FailoverGeneric Trunking (FEC/GEC)/802.3ad-Draft StaticLink Aggregration (802.3ad)I just wnat the server...

Hi,Our current scenario is, we have a Router-A cisco 2821 that is connected with two ISPs in multihoming configuration through BGP, so that if one ISP gets down the other takes over, we are receiving just a default route from our ISPs, and PIX 515E h...

Hi All,We are planning to put point to point connections between the DC and DR site for replication purpose with 2 different link's each of 655 mbps. PBR will also be configured on the switches for load distribution purposes. Good amount of real time...

amit by Level 1
  • 1308 Views
  • 5 replies
  • 0 Helpful votes

Resolved! ACL question

Hi all,I have one Extended Access list question to askif we have 2 pc with ip 5.1.1.8/24  and 5.1.1.10 /24  and we apply this acl on ethernet interface of routerwith ip access-group 101 inhere  is aclaccess-list 101 deny tcp 5.1.1.8 0.0.0.3 any eq 80...

mahesh18 by Level 6
  • 566 Views
  • 2 replies
  • 0 Helpful votes

HiI'm hoping someone can point me to articles or docs/tutorials. Basically I've been doing netwokring for about four years now, although not with anything cutting edge just normal things like nat, eigrp, ospf, bgp in standard ways, I'm looking to mov...

dan_track by Level 1
  • 519 Views
  • 3 replies
  • 0 Helpful votes

Hello,I have two switches which I have linked together with a Trunk port.On both switches i have putted several ports in a vlan. On each switch I have put a device in the vlan and they can ping each other.Only after some time (approx 2-3 minutes) I g...

Hi,I have a cisco 857 with nat for the intern net 192.168.0.0/16   ip nat inside source list 100 interface Dialer0 overload       access-list 100 permit ip 192.168.0.0 0.0.255.255 any                                     I have a full redirection to a...

osgpcqosg by Level 1
  • 428 Views
  • 1 replies
  • 0 Helpful votes

Good day everyone,I'm rather stuck configuring ACLs in our environment. Allow me to explain in detail:Our organisation is divided into 4 virtual LANs:192.168.0.0/23 (This is our live network, all our employees are using this network)192.168.4.0/24 (T...

f.jong by Level 1
  • 1488 Views
  • 8 replies
  • 0 Helpful votes
Unanswered Topics