Hi all. for a new installation with DANTE,some cisco 9300 will be used (not the usually sg350),and reading the documentation,i don´t find a way to make the changes of DSCP to Queue table.We need to change DSCP 56 set to Queue 8, DSCP46 set to Queue ...
Forum Posts
We are sending syslogs to Auvik. Auvik says none of the Cisco Catalyst 2960C 12pcL are sending logs but other cisco Catalyst models are. I do a show logging history and I see info so it is logging, just not sending it to Auvik. All the switches have ...
Hi AllHoping you can help with an issue we have with Catalyst 9300I am trying to SNAT traffic from our inside interface to our outside interface GigabitEthernet1/0/10ip nat inside source list 1 interface GigabitEthernet1/0/10 overloadip access-list s...
i HAVE FOLLOWING SCENARIO1. BRANCH 1 MPLS IP (192.168.20.1)INTERNET IP (192.168.30.1)2. BRANCH 2 MPLS IP (192.168.20.2)INTERNET IP (192.168.1.1)3. HUBMPLS IP (192.168.20.3)INTERNET IP (192.168.10.1)MY QUESTION IS ALL RELATED TO BRANCH 1. ALL SOLUTION...
Resolved! About GratuitousARP on cisco ASA/FP
Hello:Considering the following scenario:SwitchA----FP1120----SwitchB(ISP switch)The FP1120 is the FW used to replace a old fw. after FP being up, i moved the cable from the old fw to FP, like topology above.But here comes a problem, the traffic betw...
Resolved! ISR 4321 throughput max
Question on ISR 4321, right now our device is setup for 100000 kb/s throughput, however when testing iperf on our private WAN connection (which is 100mb/s) we are only getting 42mbps. We are likely hitting a throughput limit on this device? Topology...
Hello all, I have 2 stacked switches and I have updated the IOS to CAT3K_CAA-UNIVERSALK9 Version 16.3.8I there a SVI for the vlan where the clients are connected. I have set ip helper-address "DHCP IP" in this SVI, before the update it was working wi...
Hello, I am new to QoS and requested to implement QoS to prioritise Zoom Meeting traffic. Below is the configuration I have prepared for. Can anyone verify if it is correct or corrections needed. Also Customer wants that the Zoom traffic must always ...
Resolved! MST-TO-RAPID-PVST COMMUNICATION
Hello all,I am trying to setup a communication between mst and rapid-pvst. I have two switches connected to each other one has mst instance 5 with two vlans (3,4) and the other switch has rapid-pvst with same vlans. I have setup vlan interfaces on bo...
Hi everyone, I need your help. My Vlans 1, 2 and 3 must be able to communicate with each other and with the dns server. However, there must be no communication from Vlans 1,2,3 to vlan 4.On the other hand, vlan 4 must be able to communicate with ever...
Hi So i have a bunch of 2960-X (WS-C2960X-48FPS-L) and i am trying to upgrade the IOS via SCP. archive download-sw scp://admin:Password@192.168.5.149/c2960x-universalk9-tar.152-7.E4.tar!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!...
Hello guys,can I connect an Nexus 7000 with linecard N7K-F248XP-25E: , to an Fortigate 140D via Twinax Cable:Cisco SFP-H10GB-CU3MThanks in advance,Lorenz
I have (3) switches which are connected together in a redundant configuration. The connection between the SludgeBLDG and DigestBLDG switches are using ports Gig1/0/3-4. I have manually set the port cost for all VLANs to 100 but am still unable to con...
Resolved! Cisco acl
Dec 6 11:23:21.642: %FW-6-DROP_PKT: Dropping udp session 172.20.34.14:55599 8.8.8.8:53 on zone-pair inside-to-vpn class class-default due to DROP action found in policy-map with ip ident 0*Dec 6 11:24:06.219: %FW-6-LOG_SUMMARY: 1 packet were dropped ...
I am a seasoned Netacad instructor. I am trying to create a Packet Tracer PKA so that when the student opens it, it comes up in physical mode, in the Wiring Closet, ready for the student to cable and configure. Can anyone point me in the right direct...
