Hi.There is a 6506 with two supervisors:Supervisor Engine 32 8GE WS-SUP32-GE-3BOn supervisor was in active mode while another one was in hot mode:5 9 Supervisor Engine 32 8GE (Active)6 9 Supervisor Engine 32 8GE (Hot)One day 6506 unexpectedly...
Hi.There is a 6506 with two supervisors:Supervisor Engine 32 8GE WS-SUP32-GE-3BOn supervisor was in active mode while another one was in hot mode:5 9 Supervisor Engine 32 8GE (Active)6 9 Supervisor Engine 32 8GE (Hot)One day 6506 unexpectedly...
Hi every body.According to my book, eigrp uses following formula for metric calculation by default( only bandwidth and delay).m= { (10 exp 7/bandwidth) *delay}*256Let say router receives two updates about a network 10.0.0.0.First update list delay 20...
Hello, I just configured PBR on my 3750 but it's not working. Please helpI configure the ACL and the route-map, apply to interface but traffic is not working as it should. Any ideas?
Would someone point me to a white sheet, or section of a config guide, that would explain all the flags in the 'sh ip mroute' display? I looking for something more enlightening than just a discription of the flag; ie. "'The SPT-bit set' means the Sho...
HiWhy do we have the command "switchport access vlan 401 " for this interface when it is trunking interface GigabitEthernet0/47 description trunk downlink switchport access vlan 401 switchport trunk allowed vlan 400-510 switchport mode trunk
I have been reading and reading and trying to figure out the defaults for 'ip cef' and 'ip cef distributed' on Catalyst Switches.i.e. 3750, 3560s, 2950s, 2940s, 4500s and 6500s.Wouldn't/Isn't the default that Cisco Expressing Forwarding is enabled.Th...
We just upgraded the switch to a Sup720, dual 3000W power supplies and a WS-X6748-GE-TX module. How do I disable inline power on ALL the modules? Here is the output from sh power:hq1rtr02#sh powersystem power redundancy mode = combinedsystem power ...
I received a 3560 replacement switch without an IOS. I have the IOS for the switch on hand. What would be best practice to load a new IOS on a 3560 switch?
I have a pair of 6513's each connected to the same ISP via POS. Occasionally I see the attached messages in the logs and not being very comfortable with BGP I'm not too sure about who's not speaking to who!Is the ISP dropping connection or are the tw...
By mistake I got rid of the IOS file from my switch. I downloaded the version 121-22.EA13 and now I got an error saying DRAM is not sufficient and I can't find a version that will fit.
Help with routing issues.Presently a new router is in place which connect to a firewall, then, it connects to the internet.The router is configure with four vlans, but only two subnets are allow to access the internet. VLAN 100 and VLAN 200 are just ...
Hi allIf I have a 2 meg wan circuit for example, is it 2 meg down and 2 meg up, at the same time, or would it be possible only to upload at 1 meg and download at 1 meg at the same time ?
I want to implement VSS in a campus, but the documentation I read always refers to set up L3 (NSF)protocols. The issue is I only want VSS in L2. It is possible?
I'm configuring public wireless access and want to keep it off the corp network. I have a wireless LAN contoller trunked to the Cat3560 also.I cannot wrap my head around the PBR to get this to work!Interface VLAN1ip address 10.0.0.254 /24desc Corp L...
Greetings:I already read the article in resetting password. Im resetting a live network device router 2600. Can anyone give me assurance that when I perform the reset command in console, are all the configuration will not be affected after reset the ...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
10-16-2024 12:15 PM | ||
10-15-2024 03:13 AM | ||
10-14-2024 02:50 AM | ||
10-09-2024 11:22 AM | ||
10-08-2024 08:34 PM |
User | Count |
---|---|
9 | |
7 | |
6 | |
5 | |
5 |