Buy or Renew
Buy or Renew

Switching

Discuss Catalyst brand switches with peers and experts.
cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
Start a conversation

Labels

Forum Posts

Start a conversation

Resolved! protocol id for EAP in ppp frame

hi every body! ppp header has protocol id feild to specify the pay load. For example protocol id 0c21 shows the ip payload in pppp frame.What is the protocol id for EAP pay load in ppp frame ?Thanks a lot!

sarahr202 by • Level 5
  • 438 Views
  • 1 replies
  • 0 Helpful votes

Resolved! 802.1x and Eap , what is the relation?

Hi every body!I just want to know what is the relation between the 802.1x and EAP ?Here is my hunch.802.1x is a security protocol which use eap to carry authentication credentials to radius server.In Eap , the term backend authentication server is us...

sarahr202 by • Level 5
  • 867 Views
  • 1 replies
  • 0 Helpful votes

Resolved! Trying to configure NM-32a on 2811

I'm having a tough time configuring my Cisco 2811 Access Server. This router has the NM-32A card.This is what I have done so far. I plugged the octal cable into bottom left port marked 8-15. I plugged cable # 2 into a switch that is turned on. This i...

Resolved! election of avfs in GLBP

Hi every body!In GLBP, routers with highest priority is elected as AVG and the router with 2nd highest priority is elected as standby router.If priorities are same, then router with higher ip address , will become AVG.Now 2nd step comes, elections of...

sarahr202 by • Level 5
  • 2601 Views
  • 8 replies
  • 0 Helpful votes

HSRP over dot1q

Is it possible to run HSRP over trunk? I have pair of Cisco 2620 and I'm trying to run HSRP with the following conifguration and without luck. Can someone tell me if it is doable or anything wrong in my config?Thanks.interface FastEthernet0/0 no ip a...

nawas by • Level 4
  • 3130 Views
  • 12 replies
  • 0 Helpful votes

Resolved! Change http password

I have the telnet and enable password for my C2950 switch, but I can't access it through http with the admin username. How can I change the http password used for that protocol by logging on the switch through telnet ?

pierrek7 by • Level 1
  • 3914 Views
  • 1 replies
  • 0 Helpful votes

QOS - Policing 6509

I have been doing policing on a 6509 to limit the bandwidth from one host to another (Netapp Snapmirror traffic). When using the following police config it produced a steady 8.5 mb stream. police cir 8500000 bc 265625 be 265625 conform-action trans...

gizbri by • Level 1
  • 571 Views
  • 3 replies
  • 0 Helpful votes

Resolved! 6509 high CPU utilization

Hello everybody, I have a situation, and y wanted to investigate if this is normal or not.On a 6509 router ( 720 supervisor ) I start a "ping X.X.X.X size 5000 repeat 100000" from the supervisor to any host, and the CPU is incremented to 100%.Can any...

luisamato by • Level 1
  • 3760 Views
  • 7 replies
  • 0 Helpful votes

Resolved! Help with sho int x/xx switchport command

I'm trying to find out if all vlans are allowed or are they pruned?? not easy to tell..ss-us-sjc-640-102#sho int gi 0/22 switchportName: Gi0/22Switchport: EnabledAdministrative Mode: static accessOperational Mode: downAdministrative Trunking Encapsul...

jonesm111 by • Level 1
  • 1325 Views
  • 5 replies
  • 0 Helpful votes

EAP

Hi every body! I was reading about EAP and its methods such as identity,mmd5 challenge etc let say backend authenticator server sends the eap message with code feild=1 specifying that it is identity request message , asking for peer identity .When ...

sarahr202 by • Level 5
  • 445 Views
  • 2 replies
  • 0 Helpful votes

Resolved! Sticky Port Security 3560

Is there a better solution to resetting sticky port security on a single port on a Catalyst 3560 SW when a PC is swapped out than:-sw(config-if)#no switchport port-security mac-address stickysw(config-if)#switchport port-security mac-address stickysw...

Policing on a 6500 not working

Hi,I have a Catalyst 6500 with PFC2 and MSFC2 running CatOS (Layer2) + IOS (Layer3). I need to configure a limit of 1Mbps on the bandwidth available for a specific VLAN so I tried to configure policing on the routing engine but it is not working.I ha...

Unknown MAC Address

Hi, I have a Catalyst 6509 running CatOS. I would like to know if the MAC address 00-d0-00-59-67-ff that appears when I type the "show module" command is a multicast MAC Address and what is it for?.mxswt_idf16a01# (enable) show moduleMod Slot Ports M...

ivelasco by • Level 1
  • 898 Views
  • 2 replies
  • 0 Helpful votes

Dual-home servers on redundant 6500s

Hi,I'm in the process of adding an additional 6509 for distribution and access (specifically for servers). If we dual-home our servers to two separate 6500s, how does one handle the IP addressing for the secondary NICs on the servers? How does the ...

Load more