There are two areas area 1 and area 2, all have L1/L2 IS-IS running.How are the routes outside ara 1 going to appear, as i L2 or i *L1 in the routing table of router A and through which interface. Please see picture attached.
There are two areas area 1 and area 2, all have L1/L2 IS-IS running.How are the routes outside ara 1 going to appear, as i L2 or i *L1 in the routing table of router A and through which interface. Please see picture attached.
If i switch the port channel mode on a blade in catos 6513 does it cause disruption to the entire blade or switch. I am switching from pagp to lacp for a nas
Hi all,We have purchased 2 6506E switches for our new branch. The problem is that one of them does not boot and it enters rommon instead. You have to force it to boot using the boot command in rommon every time it needs reboot. Below are boot configs...
This one has me stumped. I have attached a jpg to show what is going on. Basically, EIGRP 20 redistributes the default route to the switches. However, the switches are picking on the FE interface of our VOIP gateway. It should be picking up the GI0/...
Question regarding mac aging time. On a core switch such as a 6500 is there a best practice and benefit to configuring the mac aging time other than the default of 300 seconds? I have heard it is best to up this to say 84600 of there abouts.Thanks
We have a 2960-48-TC-S (LanLite software) that we want to install regular software on. We didn't realize that we had purchased the -S switch and want to upgrade it. We tried to put something other than LanLite on it but the switch said that that hard...
Hi folksI have a 6513 with one Sup720 and IOS 12.2(18)SXF5. I'm planning to install a second Sup720 and my question is this:Are there any obvious "gotchas" when installing the secondary module? More precisely, can this be done without service interru...
Hi,Does anyone share any information about how to install GNS3 on unbuntu 8.10...I'm using Ubuntu/Linux for the first time and have no idea how to run the setup of GNS...Pls help..Thanks & Regards,CM
Problem Details: iam having 1841 router in main office, isp connected s0/0, s0/1 ip 10.10.10.1 and e0/0 is connected to my proxy server(192.168.0.1), from that it is going my lan. now i want to extend 192.168.0.0 network to my branch office. This is ...
I'm trying to upgrade a 3750G-12 from ipbase to ipservices and get this message whilst trying:Error: The image in the archive which would be used to upgradeError: system number 1 does not support the same feature set.Any idea why its happening and ho...
Hi,I have connected the stack cable between two switches but it's not showing as single switch .What would be problem ?and give the web link for the configuration.
Hi,I have set OSPF to choose between two paths. Here is the output from what I have:lab_R1#sh ip route 10.254.7.1Routing entry for 10.254.7.0/30 Known via "ospf 10", distance 110, metric 28, type intra area Last update from 172.16.1.193 on Vlan1, ...
Hi,We have purchased 1841 with advance security enterprise IOS but it is not supporting SDM. I think we need add a patch in the IOS. Please let me know from where do we download this patch from cisco.comThanks in advanceSubodh
Can any one pls tell about jumbo frames?If such frames are there in the networks how they travel throught the ports?Any specail configuration is to be done on that port?
Folks:How do I get rid of this crud?crypto pki trustpoint TP-self-signed-230132480 enrollment selfsigned subject-name cn=IOS-Self-Signed-Certificate-230132480 revocation-check none rsakeypair TP-self-signed-230132480!!crypto pki certificate chain TP-...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
11-06-2024 04:49 AM | ||
11-04-2024 07:57 AM | ||
10-24-2024 11:57 PM | ||
10-23-2024 06:42 AM | ||
10-23-2024 01:37 AM |
User | Count |
---|---|
16 | |
10 | |
7 | |
6 | |
5 |